731251
8
Zoom out
Zoom in
Previous page
1/52
Next page
8
SAS-ASMS4xx - Schnelleinrichtungsanleitung
PIR-Bewegungsmelder
Beschreibung
1. Erkennungsfenster
2. LED -Anzeige
Die LED-Anzeige blinkt einmal: der Detektor wird ausgelöst und sendet ein Signal an die
Systemsteuerung.
Die LED-Anzeige zeigt „Batterie schwach“ an: tauschen Sie die Batterie aus
3. EIN-/AUS-Schalter
Stromsparmodus: Entfernen Sie die Batterien sowie die darüber liegende Schraube und
drücken Sie auf die Verriegelung, um die Abdeckung der Rückseite zu entfernen. Der Schalter
bendet sich in der Mitte der Platine. Zum Wechseln in den Stromsparmodus: betätigen Sie
den Dip-Schalter wie in Abbildung2 dargestellt.
Installation
- Setzen Sie die Batterien ein oder schließen das Gerät über einen Micro-USB-Stecker an ein
5-V-Netzteil (DC) an (nicht im Lieferumfang enthalten).
- Schalten Sie das Gerät jetzt EIN.
- Wählen Sie einen geeigneten Standort. Bringen Sie den Detektor in einem Abstand von
mindestens 2Metern zum Boden an.
- Bringen Sie die Halterung mit Schrauben an der Wand an.
- Montieren Sie den Detektor in aufrechter Position.
- Falls erforderlich, passen Sie den Winkel des Detektors an. Behalten Sie aber die aufrechte
Position bei. Richten Sie den Detektor im richtigen Winkel auf Eingangsbereiche aus.
Vermeiden Sie hierbei eine Ausrichtung auf Türen, Fenster,
Wärmequellen oder sich bewegende Objekte.
Koppeln des Bewegungsmelders mit dem Hauptgerät
1. Drücken Sie lange auf die nummerierte Taste (1 - 4) am Hauptgerät, entsprechend dem
Bereich, zu dem der Detektor hinzugefügt werden soll. Die entsprechende LED leuchtet auf.
2. Schalten Sie den hinzuzufügenden Detektor ein und/oder lösen Sie ihn aus.
a. Das erfolgreiche Koppeln wird von zwei Blinksignalen und zwei Tönen bestätigt.
b. Ein einzelnes Blinksignal mit einem einzigen Ton gibt an, dass Zubehör erkannt wurde.
c. Drei Blinksignale mit drei Tönen geben an, dass keine weiteren Detektoren hinzugefügt
werden können.
3. Wenn ein Detektor ausgelöst wird, blinkt die entsprechende Bereichs-LED.
4. Für weitere Informationen siehe SAS-ALARM400 Betriebsanleitung.
Technische Daten
Stromversorgung: 5VDC oder 3x AAA 1,5V (nicht enthalten)
Stromstärke: < 20mA (Standby-Modus: < 50uA)
Reichweite: bis 150 m
Frequenz: 433MHz
Erkennungsbereich: 8m/110°
Betriebstemperatur: -10°C ~ +55°C
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic SAS-ALARM400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic SAS-ALARM400 in the language / languages: All languages as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info