731315

Konig Electronic SAS-ALARM120 Manual

6
Zoom out
Zoom in
Previous page
1/276
Next page
ENGLISH
6
6. It’s recommended to test the alarm system for correct operation with rst
use and every 3months.
Procedure:
a) Switch the alarm unit on to ALARM or CHIME (for testing
recommended).
b) Push the ON button on the remote control to arm the alarm.
c) Wait for 20~25seconds (delay time).
d) Open every door or window one by one and check if the corresponding
LED lights up and the CHIME sounds.
e) Disarm the alarm if everything operates correct.
f) The alarm system is ready to use.
Note:
1) The alarm unit will give a conformation tone when armed or disarmed. The
tone for CHIME is dierent as for ALARM.
2) If a sensor does not need to be switched on, it’s possible to switch o every
sensor individually with the on/o switch. In this case the sensor is no part
of the alarm system anymore when armed.
3) A sensor switched to RF+ALARM will always give an alarm sound on the
sensor itself, unless the alarm unit is armed or disarmed.
4) When a sensor is triggered and the siren of the alarm unit sounds, it needs
to be switched o with on/o switch of the alarm unit. After that the alarm
unit can be switched on again. When the alarm keeps on going after arming
the system, check if every door or window is closed properly.
Installation SAS-ALARM110
1. Insert, according the diagram inside the battery compartment, (backside)
the batteries for the alarm unit (3x AA).
2. Install the door/window sensor with the adhesive tape to doors and
windows. Note: maximum 1cm distance between magnetic contact and
sensor (see gure 2). Switch on the sensor to RF or RF+ALARM. If switched
to RF+ALARM, the sensor will send, when triggered, a signal to the alarm
unit and the siren of the sensor itself will also sound. In this case the siren of
the sensor and the alarm unit will both sound.
3. Install the vibration sensor with the adhesive tape to windows (on the
glass). Switch on the sensor to RF or RF+ALARM. If switched to RF+ALARM,
the sensor will send, when triggered, a signal to the alarm unit and the siren
of the sensor itself will also sound. In this case the siren of the sensor and
the alarm unit will both sound. Note: the vibrate sensor is very sensitive.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic SAS-ALARM120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic SAS-ALARM120 in the language / languages: All languages as an attachment in your email.

The manual is 5,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info