533092

Konig Electronic KN-URC80B Manual

16
Zoom out
Zoom in
Previous page
1/112
Next page
16
Note :
For audio equipment, fi rst press the Shift button (
shift
) and then the
TV/CD button (
/
) for CD,
STB/TAPE button (
stb
/
tape
) for TAPE,
DVD/TUNER button (
dvd
/
tuner
) for TUNER or
AUX/AMP button (
aux
/
amp
) for AMP
2) Use the number buttons to enter the code 0 0 0 2. The Signal LED (
) fl ashes twice again.
3) Push 1 and count the number of times the Signal LED fl ashes; this is the fi rst number.
4) Push 2 and count the number of times the Signal LED fl ashes; this is the second number.
5) Push 3 and count the number of times the Signal LED fl ashes; this is the third number.
6) Push 4 and count the number of times the Signal LED fl ashes; this is the fourth number.
Note :
The Signal LED does not fl ash if the number is 0. The steps 3 to 6 can be carried out in any order and as many
times as may be required.
Learn feature
Alternatively, or if either in case of manual programming or with automatic programming, the correct code for your
equipment cannot be found, you may use the learn feature.
The learn feature may also be used if certain button functions of the original remote control are not included in the
database.
Positioning the KN-URC80B and original remote control (Range test)
In order to ensure that the remote control can receive the signal, both remote controls should be placed opposite
one another with their transmission diodes facing each other. The distance between both remote controls should
not be greater than 5 cm.
You may use the range test to determine the optimal position for learning the codes:
1) Press and hold the TV (
), STB (
stb
), DVD (
dvd
) or AUX (
aux
) button depending on the level that you wish to
programme until the signal LED (
) fl ashes twice.
Note
:
For audio equipment, fi rst press the Shift button (
shift
) and then the
TV/CD button (
/
) for CD,
STB/TAPE button (
stb
/
tape
) for TAPE,
DVD/TUNER button (
dvd
/
tuner
) for TUNER or
AUX/AMP button (
aux
/
amp
) for AMP
2) Enter the code 0 0 1 1 using the numeric buttons. The signal LED fl ashes twice again.
3) Now, the signal LED lights up in orange and displays the quality of the signals received.
Now place the original remote control and press and hold any button on it.
Change the distance to the KN-URC80B remote control until the signal LED lights up in green.
Note
:
Orange light indicates readiness and that the KN-URC80B is not receiving any signal.
If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).
If the signal LED lights up in green, it indicates optimal signal quality (optimal alignment for learning).
4) To end the range test, press the TV (
), STB (
stb
), DVD (
dvd
) or AUX (
aux
) button that had been pressed
earlier.
Note
:
The optimal alignment depends on the transmission strength of the signals by the original remote control and,
hence, it may vary for each remote control. This is why you need to carry out the range test with each remote
control from which you would like to learn in order to determine the optimal alignment for it.
Learning – Basic
1) Press and hold the TV (
), STB (
stb
), DVD (
dvd
) or AUX (
aux
) button depending on the level that you wish to
programme until the signal LED (
) fl ashes twice.
BA König KN-URC80B, 135x215 mm CS6.indd 16BA König KN-URC80B, 135x215 mm CS6.indd 16 12.09.2012 10:56:1112.09.2012 10:56:11
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic KN-URC80B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic KN-URC80B in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info