533089

Konig Electronic KN-URC10B Manual

11
Zoom out
Zoom in
Previous page
1/80
Next page
11
Manual TV set programming
1) Switch your TV set on.
2) Look up the brand of your TV set under “TV” in the code list. Single or multiple 4 digit codes are shown for
each brand.
3) Press and hold the TV Standby button (
) until the signal LED ( ) fl ashes twice.
4) Use the number keys to enter the fi rst four-digit code from the code list for the brand that you have selected.
The signal LED (
) fl ashes twice to indicate that the code has been accepted.
5) Test the functionality of your remote control using the TV standby button (
) and the AV button (
av
).
6) If the TV set does not respond, or only responds partially to the commands, repeat steps 3 to 5 using the next
code from the code list.
7) If the TV set responds properly to all functions, your KN-URC10B is correctly programmed and can be used.
Please note the code that was used for future reference.
My programming codes to use
TV
Automatic programming the TV set according to brand
As an alternative, and if the correct code for your TV set cannot be found for manual programming, you can use
the automatic search function by brand for programming.
1) Switch your TV set on.
2) Look up the brand of your TV set in the brand list in the appendix to this instruction manual. There is a 3-digit
brand code for each brand.
3) Press and hold the TV Standby button (
) until the signal LED ( ) fl ashes twice.
4) Use the number buttons to enter the code 1 0 0 3. The Signal LED (
) fl ashes twice to confi rm that the
search mode has been activated.
5) Use the number keys to enter the three-digit brand code from the brand list for the brand that you have
selected. The signal LED (
) fl ashes twice to indicate that the code has been accepted.
6) Hold down the TV Standby button (
) on your KN-URC10B until the TV set switches off. This process can
take several minutes.
7) As soon as the unit has switched off, push the OK button to confi rm the programming (
ok
) until the Signal
LED (
) fl ashes twice.
8) Test the functionality of your remote control using the TV standby button (
) and the AV button (
av
). If the TV
set responds properly to all functions, your KN-URC10B is correctly programmed and can be used.
Note
:
It could happen, that during the search process, the KN-URC10B fi nds several codes to which your TV set
responds, but where all buttons do not function for each code. In this case, the search process should be
re-started (steps 3 to 9) until you obtain the best code. Re-starting the search process starts at the last saved
programming.
Automatic TV search
As an alternative, or if neither manual programming nor automatic programming by brand has found the correct
code for your TV set, you can use the automatic search function.
1) Switch your TV set on.
2) Press and hold the TV Standby button (
) until the signal LED ( ) fl ashes twice. If the button is not pushed
long enough, the TV set switches off. In this case, start the programming again by switching the TV set on.
3) Use the number buttons to enter the code 1 0 0 1. The Signal LED (
) fl ashes twice to confi rm that the
search process has been activated.
4) Hold down the Standby button (
) on your KN-URC10B until the TV set switches off. This process can take
several minutes.
5) As soon as the unit has switched off, push the OK button to confi rm the programming (
ok
) until the Signal
LED (
) fl ashes twice.
BA König KN-URC10B, 135x215 mm, Entwurf 02 CS6.indd 11BA König KN-URC10B, 135x215 mm, Entwurf 02 CS6.indd 11 12.09.2012 08:36:0012.09.2012 08:36:00
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic KN-URC10B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic KN-URC10B in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info