570558

Konig Electronic KN-STUDIO91 Manual

3
Zoom out
Zoom in
Previous page
1/32
Next page
3
Synchronization
- Test button: For testing, or multiple flashes can be used.
- Sync socket: The standard 0.35 cm jack type socket on the rear panel of the unit may be used for direct
connection to a camera set to “x” synchronization. A “Radio remote control receiver” may also be plugged
into this socket.
- Photocell: The unit has a built-in photocell, enabling the unit to be triggered by the flash from any other
flash unit, or a small camera mounted flashgun. The photocell is mounted behind the red “Ready”
indicator on the rear panel.
Modeling lamp control
Set the yellow switch to “ ” to turn on the modeling lamp and keep it on all the time.
Fuse
The modeling and flash circuitry is protected by a single 7 amp fuse mounted on the rear panel. Never replace
the fuse with one of a different rating. Be sure to switch OFF the unit before changing the bulb or fuse.
Warning - high voltage
Do not touch the flashtube assembly for thirty minutes after disconnecting from the supply.
Safety precautions:
To reduce risk of electric shock, this product should ONLY be
opened by an authorized technician when service is required.
Disconnect the product from mains and other equipment if a
problem should occur. Do not expose the product to water or
moisture.
Maintenance:
Clean only with a dry cloth. Do not use cleaning solvents or abrasives.
Warranty:
No guarantee or liability can be accepted for any changes and modifications of the product or damage caused
due to incorrect use of this product.
General:
- Designs and specifications are subject to change without notice.
- All logos brands and product names are trademarks or registered trademarks of their respective holders
and are hereby recognized as such.
- This manual was produced with care. However, no rights can be derived. König Electronic can not accept
liability for any errors in this manual or their consequences.
- Keep this manual and packaging for future reference.
Attention:
This product is marked with this symbol. It means that used electrical and electronic products should
not be mixed with general household waste. There is a separate collections system for these products.
This product has been manufactured and supplied in compliance with all relevant regulations and directives,
valid for all member states of the European Union. It also complies with all applicable specifications and
regulations in the country of sales.
Formal documentation is available upon request. This includes, but is not limited to: Declaration of Conformity
(and product identity), Material Safety Data Sheet and product test report.
Please contact our customer service desk for support:
via website: http://www.nedis.com/en-us/contact/contact-form.htm
via e-mail: service@nedis.com
via telephone: +31 (0)73-5993965 (during office hours)
NEDIS B.V., De Tweeling 28, 5215 MC ’s-Hertogenbosch, THE NETHERLANDS
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic KN-STUDIO91 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic KN-STUDIO91 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info