626912
13
Zoom out
Zoom in
Previous page
1/20
Next page
GERMAN
Die in der Verpackung enthaltenen Funksteuerungen sind bereits im bistabilen
Modus programmiert und einsatzbereit. Um die Fernbedienungen neu zu
programmieren, gehen Sie wie folgt vor.
Programmierung des König Receivers oder zusätzlicher Geräte:
(Am Receiver auszuführen, Bild 1)
Der Receiver kann im monostabilen oder bistabilen Modus
programmiert werden
Diese König-Fernsteuerung kann programmiert werden, um Output 1 und
Output 2 des Receivers im bistabilen oder monostabilen Modus zu steuern.
Beispiel 1: Mit dem monostabilen Modus können Sie einen Impuls an die
Zentraleinheit eines automatischen Tors senden, um es zu önen.
Beispiel 2: Mit dem bistabilen Modus können Sie ein Gerät (wie eine
Lampe) durch einmaliges Drücken der Taste einschalten und um das Gerät
auszuschalten, müssen Sie die gleiche Taste noch einmal drücken.
Beispiel 3: Wenn Sie bei einer Lampe den monostabilen Modus verwenden,
drücken Sie die Taste, um die Lampe einzuschalten, aber wenn Sie diese Taste
loslassen, erlischt die Lampe.
Also sollten Sie den monostabilen Modus nur verwenden, wenn Sie einen
Impuls benötigen, andernfalls sollten Sie den bistabilen Modus verwenden.
Schritt 1:
Drücken Sie die Taste P1 am Receiver:
1 x zum Programmieren von Output 1 im monostabilen Modus.
2 x zum Programmieren von Output 2 im monostabilen Modus.
3 x zum Programmieren von Output 1 im bistabilen Modus.
4 x zum Programmieren von Output 2 im bistabilen Modus.
SCHRITT 2 (unmittelbar nach Schritt 1 durchführen):
Halten Sie die Taste A oder B auf der König Fernsteuerung (Bild 2), die Sie
synchronisieren möchten, gedrückt, bis die LED am Empfänger anfängt zu
blinken.
Löschen von Codes
Es gibt zwei Arten des Löschens.
A: Löschen eines einzelnen Codes:
Drücken Sie die Taste P2 ca. 2 Sekunden (die Taste loslassen); die LED wird
aueuchten, drücken Sie die Taste auf der König Fernsteuerung, die Sie löschen
möchten.
B: Löschen aller erworbenen Codes:
Drücken Sie die Taste P2, bis die LED leuchtet (ca. 8 Sekunden).
Receiver
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic KN-RFRI KIT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic KN-RFRI KIT in the language / languages: All languages as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info