533079

Konig CMP-WNROUT40 Manual

6
Zoom out
Zoom in
Previous page
1/75
Next page
6
6.4 WDS Settings
WDS (Wireless Distribution System) is used to expand wireless coverage area. This router provides three modes: Lazy,
Bridge and Repeater.
Lazy: In this mode, the connected device can be Bridge mode or Repeater mode and enter the router’s BSSID to
establish the connection.
Bridge: You can wirelessly connect two or more wired networks via this mode. In this mode, you need to add the Wireless
MAC address of the connecting device into the router’s AP MAC address table or select one from the scanning table.
Repeater Mode: In this mode, add the opposing MAC address into each own AP MAC address table manually or by
scanner to enlarge and extend the wireless radio.
Chapter 7: DHCP Server
7.1 DHCP Settings
DHCP (Dynamic Host Control Protocol) is to assign an IP address to the computers on the LAN/private network. When
you enable the DHCP Server, the DHCP Server will allocate automatically an unused IP address from the IP address pool
to the requesting computer in premise of activating “Obtain an IP Address Automatically”. So specifying the starting and
ending address of the IP Address pool is needed.
•
DHCP Server: Activate the checkbox to enable DHCP server.
•
IP Address Start/End: Enter the range of IP addresses for DHCP server distribution.
•
Lease Time: The length of the IP address lease.
Chapter 8: Upgrade Firmware
8.1 The Router provides the firmware upgrade by clicking “Upgrade” after browsing the firmware upgrade packet,
which you can download from www.nedis.nl
•
Browse: Click this button to select the upgrade file.
•
Upgrade: Click this button to start the upgrading process. After the upgrade is completed, the router will reboot
automatically.
8.2 Reboot the Router
Rebooting the Router makes the settings congured go into effect or to set the router again if setting failure occurs.
8.3 Password Change
This section is to set a new user name and password to better secure your router and network.
•
User Name: Enter a new user name for the device.
•
Old Password: Enter the old password.
•
New Password: Enter a new password.
•
Re-enter to Confirm: Re-enter to confirm the new password.
8.4 Logout
After you have nished the settings completely, in logout page click “Yes” to logout the web management page.
How to install and set-up a router on a cable or ADSL modem
Caution!
Follow these steps without skipping a step
1. Switch the modem off (disconnect from mains power).
2. Switch the PC/laptop off.
3. Connect the LAN output of the modem via LAN cable to the blue port of the router.
4. Connect one of the yellow ports via LAN cable to the PC/laptop.
5. Now switch on the modem and wait until it is fully logged in (this can take a moment).
6. Switch on the router and wait at least 30 seconds.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig CMP-WNROUT40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig CMP-WNROUT40 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Konig CMP-WNROUT40

Konig CMP-WNROUT40 Installation Guide - Dutch - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info