779152

Koga E-NOVA EVO PT PRO 2020 Manual

25
Zoom out
Zoom in
Previous page
1/140
Next page
English – 4
1 270 020 XBI | (11.02.2019) Bosch eBike Systems
the lower the speed of the push assistance function (at full
power).
uThe push assistance function must only be used when
pushing the eBike. There is a risk of injury if the wheels
of the eBike are not in contact with the ground while using
the push assistance.
To activate the push assistance, briefly press the WALK
button on your on-board computer. After activation, press
the + button within 3s and keep it pressed. The eBike drive
is switched on.
Note: The push assistance cannot be activated at assistance
level OFF.
The push assistance is switched off as soon as one of the
following occurs:
– You release the + button;
– The wheels of the eBike are locked (e.g. by applying the
brakes or hitting an obstacle);
– The speed exceeds 6 km/h.
The push assistance function is subject to local regulations;
the way it works may therefore differ from the description
above, or the function may even be deactivated completely.
Powering external devices via the USB port
The USB port can be used to operate or charge most devices
that can be powered via USB (e.g. various mobile phones).
Charging requires the on-board computer to be mounted
and a sufficiently charged battery to be inserted in the eBike.
Open the protective cover (8) for the USB port on the on-
board computer. Use a Micro-A – Micro-B USB charging
cable (available from your Bosch eBike dealer) to connect
the USB port on the external device to the USB port (7) on
the on-board computer.
Once the electrical load has been disconnected, the USB
port must be carefully resealed with the protective cover
(8).
USB connections are not waterproof. When cycling in the
rain, do not connect any external devices and make sure
that the USB port is fully sealed by the protective
cover(8).
Important: If electrical loads are connected, this can affect
the range of the eBike.
Displays and configurations of the
on-board computer
Speed and distance indicators
The speedometer (f) always displays the current speed.
You can choose from the following functions in the function
display (combination of text indicator (d) and value indic-
ator (e)):
–<Clock>: Current time
–<Max. speed>: Maximum speed achieved since the last
reset
–<Avg. speed>: Average speed achieved since the last re-
set
–<Trip time>: Journey time since the last reset
–<Range>: Estimated range of the available battery
charge (at constant conditions such as assistance level,
route profile, etc.)
–<Odometer>: Total distance travelled with the eBike
(cannot be reset)
–<Trip distance>: Distance travelled since the last reset
To switch between display functions, press the ibut-
ton(1) on the on-board computer or the ibutton(10) on the
operating unit repeatedly until the required function is dis-
played.
To reset the <Trip distance>, <Trip time> and <Avg.
speed>, switch to one of these three functions and then
press the RESET button (6) until the indicator is set to zero.
This will also reset the values of the other two functions.
To reset the <Max. speed>, switch to this function and then
press the RESET button (6) until the indicator is set to zero.
To reset the <Range>, switch to this function and then press
the RESET button (6) until the indicator is reset to the value
of the factory setting.
If the on-board computer is removed from the holder (4), all
values of the functions are saved and can still be displayed.
Displaying/adjusting basic settings
The basic settings can be displayed and changed regardless
of whether the on-board computer is inserted in the holder
(4) or not. Some settings can only be viewed and changed
when the HMI is inserted. Depending on the equipment of
your eBike, some menu items may not be present.
To go to the basic settings menu, simultaneously press the
RESET button (6) and the i button (1) until <Configura-
tion> appears on the text indicator (d).
To switch between the basic settings, press the i button
(1) on the on-board computer repeatedly until the required
basic setting is displayed. If the on-board computer is inser-
ted in the holder (4), you can also press the i button (10) on
the operating unit.
To change the basic settings, press the on/off button (5)
next to the – indicator to reduce or scroll down, or the light-
ing button (2) next to the + indicator to increase or scroll up.
If the on-board computer is inserted in the holder (4), it is
also possible to change the settings with the –(11) and
+(12) buttons on the operating unit.
To exit the function and save a changed setting, press the
RESET button (6) for three seconds.
You can choose between the following basic settings:
–<– Clock +>: Setting the current time. The time can be
changed faster by pressing the setting buttons for a
longer period.
–<– Wheel circum. +>: Changing the value pre-set by the
manufacturer by ± 5%. This menu item is displayed only
when the on-board computer is in the holder.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Koga E-NOVA EVO PT PRO 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Koga E-NOVA EVO PT PRO 2020 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 14.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info