782606
21
Zoom out
Zoom in
Previous page
1/148
Next page
21
English
Content
1 x Robot vacuum cleaner with dust container
1 x Charging station with charger
1 x Water tank
2 x Mop cover
1 x Cleaning brush
2 x Side brush sets
2 x Batteries (AAA/LR03)
1 x User manual
1 x Warranty card
Controls and components
AShock absorber
BExhaust holes
CDust container release
DDust container
EOn/Standby switch with power LED
FDC jack, vacuum robot
GCharging station
HCharging contacts
ICharge control LED
JDC jack, charging station
KDust pre-filter and fine filter
LHEPA filter
MFilter holder
NFilter bottom lid
OBrush roller
POn/ o switch
QDrive wheels
RRotary brushes
SBattery compartment with lid
TVacuum cleaner charging contacts
UDepth sensor
VCharger with charging cable and DC plug
WWater tank with mop cover and cap
(not shown)
XCleaning brush
YReplacement mop cover
Remote control
1Transmitter diode
2Vacuuming mode button
3Button forward
4Button left
5Timer button
6Button charging station
7Time button
8Button backward
9Button right
10 Start / Pause button
11 Mode button
12 Display
Assembly
Charging station
Fig. 1 Insert the DC plug of the charger into
the DC socket on the charging station.
Connect the power adaptor to the
mains.
Fig. 2 Place the charging station against the
wall, so that the vacuum robot can return
to the charging station independently.
Pay attention to the required clearances
at the charging station.
Note:
Remove any objects within 1 meter from
either side of the station and 2 meters from
the front of the station.
Fig. 3 Press the two rotary brushes labelled
L and R onto the brackets until they
click into place. Pay attention to the
designation L and R on the device as
well as the brushes..
Remote Control
Fig. 4 Open the battery compartment on the
back of the remote control. Insert two
AAA / LR03 batteries into the battery
compartment. Observe the correct
polarity (+/-) according to the imprint.
Charging the battery
Fig. 5 Switch on the vacuum robot with the
on/ o switch on the bottom (I). Set it
down in front of the charging station.
Press the on/ standby switch on the
vacuum robot or the charging base
button on the remote control and
then immediately the charging station
button. Make sure the robotic vacuum
cleaner is moving to the charging
station. Before first time use the
built-in batteries must be charged for
at least 12 hours. Subsequent charging
processes will take approx. 4-6 hours
when the battery is empty.
Alternatively, for charging, the DC plug
of the charger can also be connected
directly to the DC socket on the vacuum
robot.
Note:
• Make sure that the charging contacts of
the robot vacuum cleaner and charging
base are not dirty. Clean the contacts if
necessary.
• It is normal for the charging base and
vacuum cleaner to become hot during
charging. This is not a cause for concern.
• Remove the water tank before charging
the robot vacuum cleaner.
Fig. 6 When the battery is charging, the on/
standby switch LED flashes blue. When
the battery is charged, the LED is on
permanently.
LED indicator
LED color Condition
Permanently blue Battery is fully charged
Blue flashing During charging
Indicator light o Product is switched o
Permanently red Brush roller is blocked
and has to be cleaned
Fig. 7 If the old battery is worn, it can be
replaced by a replacement battery (not
included in the delivery).
Remove the screws and the battery
compartment cover and remove the old
battery. Insert the new battery in the
correct direction to the connector. Close
the battery compartment and tighten
the two screws.
IM_KRVC2320RC_190807_V10_HR.indb 21 7/8/2019 14:43
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Koenic KRVC 2320 RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Koenic KRVC 2320 RC in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 9.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info