212640
68
Zoom out
Zoom in
Previous page
1/76
Next page
64 A-61550 July 2008
Problem solving Use the chart below as a guide to check possible solutions to problems
you may encounter when using the Kodak i1400 Series Scanner.
Problem Possible Solution
The scanner will not scan/
feed documents
Make sure that:
the power cord is plugged in and the power is on.
the scanner cover is completely closed.
the proper power-up sequence was followed, the scanner’s green light
is on, and the software has enabled scanning.
documents are making contact with the feed module.
the height of batched documents is less than 10.2 mm (0.4 in.) or
approximately 150 sheets of 60 g (16 lb.) paper.
documents meet specifications for size, weight, and type, etc.
for thicker documents, you lift the gap release lever during feeding.
you check the feed module and separator module for signs of wear,
and replace these parts if necessary.
You can also power the scanner down and power up again.
Image quality is poor or has decreased Make sure that the scanner is clean. Refer to Chapter 5, Maintenance.
Documents are jamming Make sure that:
the output tray and guides are adjusted for the length and width of
documents being scanned.
all jammed documents have been removed from the paper
transport area.
documents meet specifications for size, weight, and type, etc.
all staples and paper clips have been removed from the documents.
the separator module and feed module are clean and properly
installed.
the drive rollers are clean.
the imaging guides are clean.
“False” paper jams are occurring Make sure that the paper transport area is clean.
35.6 cm (14 in.) or longer documents
are not feeding or are jamming
Make sure that the input and output tray extenders are pulled out to
provide support for long documents.
The lamps shut off too soon The lamps in the i1400 Series Scanners will turn off after 15 minutes of
no scanner activity. If the lamps are off, but the scanner has not yet gone
into the Energy Star mode (default 15 minutes), there will be a delay of
about 10 seconds for the lamps to warm up again.
If you set the Energy Star timeout to a new value greater than 15
minutes, you must scan at least one document for that setting to be
enabled. After this setting has been enabled, it will be enforced until a
new setting is selected or the scanner is powered off and back on.
Cannot scan after Standby or Hibernate
with Microsoft Windows Vista
Upgrade to Service Pack 1 or higher.
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kodak i1420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kodak i1420 in the language / languages: English as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kodak i1420

Kodak i1420 User Manual - Dutch - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info