Manual Klipsch RT-10d (page 3 of 36) (English, German, French, Italian, Portuguese, Spanish)

588337

Zoom out

Zoom in

1/36

in the selected preset the display will read “Preset Empty.” From

this screen press the down or up cursor key to access other

control settings.

“EQ Mode:” - This screen is used to select two different Bass

emphasis settings, titled “Punch” and “Depth”. They are designed

to complement different types of program material, such as

movie soundtracks or music. The “Punch” setting emphasizes the

55Hz region while the “Depth” setting boosts the 30Hz range. A

third setting is titled “Flat” which defeats these two settings. Use

the Left/Right cursor keys to select the desired EQ setting. From

this screen press the down or up cursor key to access other

control settings.

“Room Correction On / Off” – This screen indicates whether

the “Room Correction” filter, mentioned below, is engaged. Press

either the Right/Left cursor keys to turn this function on or off.

This screen will not appear if the “Room Correction” function has

not been activated, the “Room Correction” calibration was unsuc-

cessful or the user memories have been erased using the

“System Reset” function described under the “Save Settings”

section of this manual.

“Lowpass” – This screen is used to adjust the subwoofer’s

upper frequency limit to achieve a proper blend with your sys-

tem’s main speakers. A higher frequency (Hz) is typically used

with smaller, bass limited main speakers and a lower frequency

setting is customarily used with larger floorstanding models. This

filter can be adjusted from 40Hz to 120Hz, as required, or

defeated if the low pass filter function is being performed by your

system’s electronics. Use the Left/Right cursor keys to adjust the

lowpass filter. To defeat this filter press and hold the Right cursor

key until “Lowpass OFF LFE Mode” is displayed. Refer to your

surround processor’s owner’s manual for more Bass

Management information. From this screen press the down or

up cursor key to access other control settings.

“Lowpass Slope” - This screen is used to adjust how aggres-

sively the subwoofer rejects frequencies above the low pass

filter’s setting. This screen is not visible if the “Lowpass” filter

above is set to “Lowpass OFF LFE Mode”. There are four settings

to choose from; “18, 24, 36 & 48 dB/Octave”. The higher the

number the more the upper frequencies are removed from the

subwoofer’s output. Use the Left/Right cursor keys to select the

desired filter slope. Start with either the 24 or 36dB/Octave

setting and adjust from there if required. Adjustment of this

parameter can help to optimize the acoustic blend with your

main speakers. The proper setting will depend on room

acoustics, your main speaker’s performance and the placement

of the speakers and subwoofer in the room. From this screen

press the down or up cursor key to access other control settings.

CONTROLS

All of the subwoofer’s controls, and changes to control settings,

are accessed through the cursor key pad and display on the top

of the subwoofer’s cabinet. The only exception to this is the main

AC power switch which is located on the rear panel of the sub-

woofer.

• Use the (UP) or (Down) key to scroll through the list of

control options.

• Use the (Left) or (Right) Key to make adjustments to a

given control setting

• Use (Enter Key) when the “ ” appears on the display

to store and recall custom settings or to lock the keypad

• After adjusting the individual control parameters for “Volume”,

“EQ Mode”, “Lowpass”, “Lowpass Slope” and “Phase”,

your settings can be stored in one of Five user memories

(“Movie”, “Music”, “Night”, “User 1” and “User 2”). This allows

for global recall of all of the above settings to tailor the

subwoofer’s performance to compensate for differing source

material and uses.

• The display backlighting will turn off if no keypad inputs are

made for 10 seconds.

• The display will return to the “Volume” screen if no keypad

inputs are made 10 for seconds.

• If the display is in standby mode, the initial button press will

turn on the display backlighting. The second button press will

initiate a control adjustment or the selection of another mode.

• In periods of low humidity, it is possible that a static electricity

discharge to the subwoofer may cause a momentary

interruption in the subwoofers output or changes to the LCD

display content. Any display content errors will be corrected

when the screen changes modes.

“Volume” – Use the Left/Right cursor keys to adjust the sub-

woofer’s volume level to match the output of your main speak-

ers. Press and hold (or press and release) the Left cursor key to

decrease the subwoofer’s volume. Press and hold (or press and

release) the Right cursor key to increase the subwoofer’s volume

to the desired level. From this screen press the down cursor key

to access other control settings.

“Recall Settings:” – This screen is used to select any one of

five user defined memory presets titled “Movie”, “Music”, “Night”

“User 1” and “User 2”. Use the Left/Right cursor keys to select

the desired group of stored control settings and press the Enter

key “ ” to apply them. “Settings Recalled!” will then be dis-

played. During initial setup, skip this screen until all other initial

control adjustments have been made. If nothing has been saved

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Klipsch RT-10d in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Klipsch RT-10d Manual

Product: