588342
3
Zoom out
Zoom in
Previous page
1/30
Next page
CONNECTIONS AND CONTROLS
CAUTION: Turn off your amplifier and your subwoofer before
making any connections. Do not connect both the “High
Level” and “Line Level” inputs at the same time as damage
to your equipment could result.
RW-10d / RW-12d / RSW-10d
“LINE IN” -
This input is designed as the standard or default
input for the subwoofer. It accepts signals from the Left and
Right channel pre-amp, subwoofer or LFE outputs of your elec-
tronics via the RCA jack inputs. Connect to the “RIGHT” and/or
“LEFT/LFE” inputs on the subwoofer’s rear panel (Refer to
figures 3 and 5).
RW-10d / RW-12d
“HIGH LEVEL IN”
- These connections can be used as an
alternate connection method to the line level hook up. Using
16- gauge or larger speaker wire, connect the Red “positive” (+)
terminal of your amplifier’s Left channel to the Red “positive” (+)
terminal of your subwoofer’s Left channel ”HIGH LEVEL IN”
terminal. Connect the Black “negative” (-) terminal of your ampli-
fier’s Left channel to the Black “negative” (-) of your subwoofer’s
Left channel ”HIGH LEVEL IN” terminal. Repeat this procedure for
the Right channel connections (refer to Figure 4). Take care that
no bare wires from any of the connections can touch any of the
other terminals as damage to your equipment could result.
CONTROLS
All of the subwoofer’s controls, and changes to control settings,
are accessed through the cursor key pad and display on the top
of the subwoofer’s cabinet. The only exception to this is the main
AC power switch which is located on the rear panel of the
subwoofer.
• Use the (UP) or (Down) key to scroll through the list of
control options.
Use the (Left) or (Right) Key to make adjustments to a
given control setting
Use (IE Center Key) when the “ ” appears on the display
to store and recall custom settings or to lock the keypad
After adjusting the individual control parameters for “Volume”,
“EQ Mode”, “Low-pass filter” and “Phase”, your settings can
be stored in one of three user memories (“Movie”, “Music”
and “Night”). This allows for global recall of all of the above
settings to tailor the subwoofer’s performance to compensate
for differing source material and uses.
The display will return to the “Volume” screen after 10
seconds if no adjustments are made while in any other control
or display mode.
In periods of low humidity, it is possible that a static electricity
discharge to the subwoofer may cause a momentary
interruption in the subwoofers output or changes to the LCD
display content. Any display content errors will be corrected
when the screen changes modes.
“Volume” - Use the Left/Right cursor keys to adjust the
subwoofer’s volume level to match the output of your main
speakers. The volume control on your system’s main amplifier
or pre-amplifier will be the overall volume control for your
subwoofer and full range speakers. Press and hold (or press and
release) the Left cursor key to decrease the subwoofer’s volume.
Press and hold (or press and release) the Right cursor key to
increase the subwoofer’s volume to the desired level. From
this screen press the down cursor key to access other control
settings.
“Recall Settings:” - This screen is used to select any one of
three, user defined, memory presets titled “Movie”, “Music” and
“Night”. Use the Left/Right cursor keys to select the desired
group of stored control settings and press the Center key to
apply them. “Settings Recalled!” will then be displayed. All of the
user settings, in the three memory presets, can be erased and
restored to their default values by scrolling down to the last
“System Info” screen. Press the Right cursor key twice to get to
the “System Reset” screen. Press the center cursor key and all
user settings will be replaced with the default settings. “Reset
Complete” will be displayed. During initial setup, skip this screen
until all other initial control adjustments have been made. From
this screen press the down or up cursor key to access other
control settings.
“EQ Mode:” - This screen is used to select two different Bass
emphasis settings, titled “Punch” and “Depth”. They are designed
to complement different types of program material, such as
movie soundtracks or music. The “Punch” setting emphasizes the
60Hz region while the “Depth” setting boosts the 30Hz range. A
third setting is titled “Flat” which defeats these two settings. Use
of either of these EQ settings will slightly reduce the subwoofer’s
maximum output capability as they will require more of the
subwoofer’s amplifier power. Use the Left/Right cursor keys to
select the desired EQ setting. From this screen press the down
or up cursor key to access other control settings.
“Lowpass” - This screen is used to adjust the subwoofer’s
upper frequency limit to achieve a proper blend with your
system’s main speakers. A higher frequency (Hz) is typically used
with smaller, bass limited main speakers and a lower frequency
setting is customarily used with larger floorstanding models. This
filter can be adjusted from 40Hz to 120Hz, as required, or
defeated if the low pass filter function is being performed by your
system’s electronics. Use the Left/Right cursor keys to adjust the
lowpass filter. To defeat this filter press and hold the Right cursor
key until “Lowpass OFF LFE Mode” is displayed. Refer to your
surround processor’s owner’s manual for more Bass
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Klipsch RSW-10d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Klipsch RSW-10d in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info