584806
6
Zoom out
Zoom in
Previous page
1/11
Next page
Page 10 Page 11
Connecting the Loudspeakers - 4Connecting the Loudspeakers - 3
Bi-amping and Tri-amping
Connecting each loudspeaker drive element to separate amplication oers the highest possible performance
level. It is not necessary for the ampliers in the treble and bass sections to be identical. In fact for tube ampli-
er enthusiasts, there are advantages to using smaller ampliers in the treble and midrange sections as the
smaller transformers oer the signicant possibility of extended, sweeter treble response.
To multi-amp, the following criteria are essential:
The ampliers should be phase coherent. In other words, all ampliers should be, by design, phase non-invert-
ing or phase inverting, or if not, should be connected so as to be all phase non-inverting or phase inverting.
The ampliers must have identical voltage gains, or should be set up to have identical voltage gains.
The ampliers must have low residual noise characteristics, especially in the midrange and treble sections.
Ampliers in corresponding channels must be identical; i.e., both bass ampliers must be the same and so on.
If any of the above conditions are not met, separate amplication will be signicantly worse than ordinary
bi- or tri-wiring. If you are unsure about these concepts or unsure if your ampliers meet these criteria, it is es-
sential that you consult your Klipsch specialist dealer before proceeding further.
Bi-amping
The Mid/Treble amplier is bi-wired
(One channel shown)
Important Note. After connecting and placing the loudspeaker upright, the connections will be hidden from
view. We strongly recommend that you identify each cable to eliminate possible diculties down the line.
Bi-wiring
Bi-wiring reduces unwanted interactions between the bass drivers and the midrange and treble units.
True bi-wiring is connecting separate cables from the bass terminals and the midrange/treble terminals to a
common connection at the amplier. Several cable manufacturers produce specialized cables where one cable
jacket contains four cables, thus enabling bi-wiring within one cable cluster. This eliminates the need to run
separate cables and simplies connection. In any case, the method of connection is the same.
Prepare the crossover panel as shown on the previous page. Proceed as for standard wiring, but connect one
cable to the bass terminals of the speaker. Connect a second cable to the midrange and treble terminals. Refer
to the diagram. After connection, tighten all the terminals with the supplied wrench as shown previously.
HFHF
MFMF
LFLF
LFLF
HFHF
MFMF
Right Speaker Left Speaker
AMPLIFIER
Tri-wiring
The logical extension to bi-wiring is tri-wiring, where all the elements of the loudspeaker are separately con-
nected to the amplier.
To tri-wire, you need to remove all the straps connecting the terminal pairs and then connect three cables as shown
in the diagram below. After connection, tighten all the terminals with the supplied wrench as shown previously.
HFHF
MFMF
LFLF
HFHF
MFMF
LFLF
Right Speaker Left Speaker
AMPLIFIER
Important Note. After connecting and placing the loudspeaker upright, the connections will be hidden from
view. We strongly recommend that you identify each cable to eliminate possible diculties down the line.
HFHF
MFMF
LFLF
HFHF
MFMF
LFLF
Tri-amping
(One channel shown)
MID /
TREBLE
AMP
BASS
AMP
TREBLE
AMP
MID
AMP
BASS
AMP
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Klipsch P-39F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Klipsch P-39F in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Klipsch P-39F

Klipsch P-39F User Manual - Spanish - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info