584810
6
Zoom out
Zoom in
Previous page
1/11
Next page
Page 10 Page 11
Connecting the Loudspeakers - 3
Bi-amping
Connecting each loudspeaker drive element to separate amplication oers the highest possible performance
level. It is not necessary for the ampliers in the treble and bass sections to be identical. In fact for tube ampli-
er enthusiasts, there are advantages to using smaller ampliers in the treble and midrange sections as the
smaller transformers oer the signicant possibility of extended, sweeter treble response.
To multi-amp, the following criteria are essential:
The ampliers should be phase coherent. In other words, all ampliers should be, by design, phase non-invert-
ing or phase inverting; or if not, should be connected so as to be all phase non-inverting or phase inverting.
The ampliers must have identical voltage gains, or should be set up to have identical voltage gains.
The ampliers must have low residual noise characteristics, especially in the midrange and treble sections.
Ampliers in corresponding channels must be identical; i.e., both bass ampliers must be the same and so on.
If any of the above conditions are not met, separate amplication will be signicantly worse than ordinary bi-
wiring. If you are unsure about these concepts or unsure if your ampliers meet these criteria, it is essential that
you consult your Klipsch specialist dealer before proceeding further.
Bi-amping
The mid/treble amplier is bi-wired
(One channel shown)
Bi-wiring
Bi-wiring reduces unwanted interactions between the bass drivers and the midrange and treble units.
True bi-wiring is connecting separate cables from the bass terminals and the midrange/treble terminals to
a common connection at the amplier. Several cable manufacturers produce specialized cables, where one
cable jacket contains four cables, thus enabling bi-wiring within one cable cluster. This eliminates the need to
run separate cables and simplies connection. In any case, the method of connection is the same.
Prepare the crossover panel as shown on the previous page. Proceed as with standard wiring, but connect one
cable to the bass terminals of the speaker. Connect a second cable to the midrange and treble terminals. Refer
to the diagram. After connection, tighten all the terminals with the supplied wrench as shown previously.
HFHF
Right Speaker Left Speaker
AMPLIFIER
MID /
TREBLE
AMP
BASS
AMP
Page 11
Connecting the Loudspeakers - 2
The Terminal Panel
As supplied, positive and negative terminals of the high and low frequency terminal pairs are strapped to-
gether with a two-way strap. This is how you should prepare the terminal panel for each wiring option.
Standard (Single) Wiring
The straps are left in place as supplied. Connection may be made to any pair of terminals.
You will need two loudspeaker cables of equal lengths, one for each loudspeaker.
Partially unscrew one positive and one negative terminal. Connect the positive (+ RED) terminal of the loud-
speaker to the striped conductor, or (if you are using custom cable) to the conductor designated by the cable
manufacturer. Connect the negative (– BLACK) terminal to the plain conductor. Do not connect the amplier
at this time.
Bi-wiring Connection
Loosen the terminals.
Remove the straps
Re-tighten all
terminals hand tight
HFHF
Right Speaker Left Speaker
AMPLIFIER
Standard Connection
No preparation
needed
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Klipsch P-27C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Klipsch P-27C in the language / languages: English as an attachment in your email.

The manual is 1,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info