584725
2
Zoom out
Zoom in
Previous page
1/6
Next page
3. To install the tilebridge, fold the rail side of the ring back
upon itself using the spring tensioner on the reinforcement ring
to allow insertion into the cutout hole. Once it is inserted into
the cutout hole, release the reinforcement ring such that it
unfolds back to its normal position. Position tilebridge over
cutout hole.
4. The wiring compartment is intended as a termination point
for the audio circuit. Access to this compartment is gained by
removing the terminal cover located on the back of the
speaker. The terminal cover will accept the appropriate
conduit/wire adapter. Feed wires through conduit/wire
adapter and connect to the input terminal according
to the desired operation mode. Be sure to observe
proper polarity. Replace the terminal cover and tighten the
conduit/wire adapter to secure the wire.
Caution: When connecting 70V or 100V distributed
line systems, take care to ensure proper terminal
connection. Connection to the low impedance termi-
nal could result in speaker damage, amplifier
damage, or both.
Thank you for purchasing your
Klipsch IC-SW-8T2 in-ceiling subwoofer.
The IC-SW-8T2 in-ceiling speaker is designed for music reinforce-
ment applications. Unobtrusive, these loudspeakers are engi-
neered for easy, versatile installation.
The IC-SW-8T2 features a transformer-less design for 70.7V/100V
distributed-line systems. Some of the benefits of this design are:
Elimintation of transformer saturation at high output levels,
elimination of transformer insertion losses, improved bandwidth
(particularly at low frequencies), and improves power transfer to
the loudspeaker at low frequencies. For applications where 4
ohm mono or 8 ohm stereo operation is required, the mode of
operation can be selected by using an optional connection
located on the back input terminal and by properly setting the
rotary switch located under the grill.
Before installing your speakers take a moment to check the
contents of the cartons and make sure nothing has been
damaged in transit.
Contents Description Q
UANTITY
Speaker Module 1
Grille 1
Reinforcement Ring 1
Rails 2
Cardboard Cutout Template and Paint Mask 1
Screws (Attach Rails to Reinforcement Ring) 2
3/
8"
Adapter Fittings 1
1/
2"
Adapter Fittings 1
Installation Guidelines
The IC-SW-8T2 includes a tilebridge for use when installing
the loudspeaker into suspended ceilings or wher
ever additional
reinforcement of the ceiling material is required. The tilebridge
and loudspeaker are designed such that installation may be
accomplished where access above the ceiling is not possible
or may be difficult.
Installation
1.
The tilebridge is composed of three parts—a reinforcement ring
and two rails. The two rails should be attached to the
reinforcement ring using the two included screws as shown below.
Caution: Be sure to comply with any and all building codes
in your area.
2. To install your IC-SW-8T2 cut out a hole in the ceiling using
either the cardboard cutout template provided with your speak-
ers or consult the measurements below. Pull wiring through hole.
I C - S W -8T2
IC-SW -8T2 12.5 " Round
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Klipsch IC-SW-8T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Klipsch IC-SW-8T 2 in the language / languages: English as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info