Manual Klipsch Heritage (page 3 of 37) (English, German, French, Italian, Portuguese, Spanish)

584715

Zoom out

Zoom in

1/37

three-speaker stereo array. It provides the full range bass

response of the Klipschorn with sensitivity and output

approaching the fully horn-loaded models. Like the Heresy, the

Cornwall is a three-way design utilizing horn-loaded compres-

sion drivers for midrange and treble frequencies and a direct

radiating 15-inch woofer for the low frequencies.

HERESY III

First introduced in 1957, the Heresy started life as a compact

center channel speaker for the Klipschorn in three-speaker

stereo arrays. The Heresy is a compact, three-way design that

uses horn-loaded compression drivers for midrange and treble

reproduction and a direct radiating 12-inch woofer for the low

frequencies.

UNPACKING & ASSEMBLY

Heresy III and Cornwall III

The Heresy III and Cornwall III models are large, heavy speak-

ers. It is recommended that two people unpack and install

these models. Open the top carton flaps, invert the carton and

pull it up and off of the speaker. Remove the internal packing

and save for future use.

Klipschorn and LaScala II

The Klipschorn and La Scala II low and high frequency

cabinets are shipped in two separate cartons. These are large,

heavy speakers. Unpacking and setup will require two people.

The Klipschorn and LaScala II high and low frequency

cabinets are matched by serial number for proper

acoustic performance. Please take care to match upper

and lower cabinet serial numbers when assembling these

loudspeakers.

Klipschorn

Open the flaps of the larger low frequency carton labeled

“Open This End”, invert the carton and lift it off of the speaker

cabinet and remove the inner packing. The top of the cabinet,

with its three rubber spacers, should be facing up (See Figure

1). Slide the bass cabinet into the corner where it will be

placed for a test fit and make note of any obstructions that

interfere with a tight fit. Remove the cabinet from the corner to

install the high frequency cabinet. Position the speaker near,

but not tight into, the corner and remove the low frequency

grille (two wing nuts) on the input panel side of the cabinet

and set aside until the connection process is complete.

Open the top flaps of the smaller high frequency carton

marked “Open This End” and remove the packing pad. Lift the

high frequency cabinet out of the carton and set it on top of

the low frequency cabinet. Align the three rubber bumpers on

the top of the low frequency cabinet with the three recesses

on the underside of the high frequency cabinet. Thread the

high and mid frequency driver leads in the upper cabinet

through the hole in the cabinet’s lower panel. Connect the

Green (+) tagged pair of wires to the pair of binding posts

labeled “Tweeter Out.” Take care to match the Red (+) and

Black (-) binding posts with the Green (+) and Black (-)

sleeves on the ends of these wires. Follow this same proce-

dure to connect the Yellow tagged pair of wires to the pair of

binding posts labeled “Mid Out.” (See Figure 5.)

La Scala II

Open the flaps of the larger low frequency carton labeled

“Open This End.” Invert the carton, lift it off of the speaker

cabinet and remove the inner packing. The top of the cabinet,

with its three rubber spacers, should be facing up (See

Figure 2).

For the La Scala II high frequency cabinet, open the top flaps

of the smaller carton marked “Open This End,” and remove the

inner packing pad. The bottom of the cabinet should be facing

up with the low frequency connection cable attached to it. Free

this cable, invert the carton and lift it off the cabinet. With

assistance, lift the high frequency cabinet off the floor and

place it on top of the low frequency cabinet while placing the

low frequency cable toward the rear and out the gap between

the cabinets. Align the recesses on the bottom surface of the

high frequency cabinet with the rubber bumpers on the top of

the low frequency cabinet. Connect the low frequency cable to

the two screw barrier strip on the rear of the low frequency

cabinet. Be sure to observe proper polarity by connecting the

wire with the Red Indicator to the terminal with the Red mark-

ing and the wire with the Black indicator to the other terminal.

PLACEMENT

Your Klipsch Heritage loudspeakers will perform well in a

variety of locations but best results will be achieved using the

following general guidelines:

• All: Place on a common wall 6 to 15 feet apart.

• La Scala, Cornwall, Heresy: Position them equidistant from

the wall behind the speakers.

• Heresy: Equidistant height above the floor with the high

frequency drivers at seated ear height if wall or cabinet

mounted.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Klipsch Heritage in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Klipsch Heritage Manual

Product: