584780

Klipsch Gallery Series Manual

4
Zoom out
Zoom in
Previous page
1/20
Next page
SPEAKER/SOUNDBAR ON-WALL INSTALLATION
If you mount your G-12,G-16,G-28 speakers or G-42 soundbar on a wall, do
not attach the pedestals. Determine a suitable location for each speaker to
wall-mount and complete all wiring to all speaker positions before mounting
speakers to the wall. Do not ceiling-mount.
1. If you have the G-28 or G-42, use included template and choose mount
position for the speaker (horizontal or vertical). Pin template to wall, mak-
ing sure it is level (when horizontally mounting) or plumb (when vertically
mounting) and positioned correctly, centered with the TV’s center points for
example. Mark on wall the pilot hole locations through the template and
remove template. If you have the G-12 or G-16, mark on wall 2 pilot hole
points 9.26”apart for the G-12 or 13.25”apart for the G-16 (make sure
the points are lined up so that the speaker hangs straight up and down verti-
cally or level horizontally). For all speakers, Leave a minimum of one inch
space between speaker cabinet and TV. Keep in mind that, when mounted,
the speaker will “lock” into position 5/16” lower than where the pilot holes
are drilled.
2. Pre-drill pilot holes in marked locations. If drilling into a wall stud (ideal) it is
recommended to use #10 mounting screws (not included) to mount the
speaker bracket (G-28 and G-42) or the speaker itself (G-12 and G-16).
If there is no stud where a pilot hole is located, install wall anchors (not
included) into the pilot holes to hold the bracket or speaker instead. Wall
anchors should be rated to at least 6 pounds (G-12 and G-16) or 12 pounds
(G-28 and G-42).
3. If vertical wall-mounting, feed speaker wire into speaker bottom area
and attach each wire to appropriate screw-terminal binding post (See
Diagram 2). If horizontal wall-mounting, feed speaker wire to channel(s)
that start on the back center part of the speaker, then continue run-
ning wire through the channel(s) and attach each wire to the appropri-
ate screw-terminal binding post the same as if vertical mounting. (See
Diagram 3) (Note: using speaker wire larger than 18 gauge may
not allow wire(s) to completely fit in channels). If needed, stick the
included adhesive strip on a point over the channel to hold the wires
in place in the channel. To change the Klipsch logo direction on the
speaker front gently pull out one side of it and rotate 45˚.
4. Gently push the speaker onto the two tabs on the mounted bracket through
its keyholes (G-28 and G-42) or onto the two screws in the wall (G-12 and
G-16) and push 5/16” down to lock into position.
CONNECTING
G-12,G-16,G-28 Connection - Using 16-gauge or larger speaker wire, con-
nect the RED “positive” (+) terminal of the LEFT speaker to the RED “positive”
(+) terminal of your amplifier’s LEFT channel. Connect the BLACK “negative” (-)
terminal of the left speaker to the BLACK “negative” (-) terminal of your amplifier’s
left channel. Repeat this procedure for connecting all remaining speakers to the
appropriate amplifier channels.
G-42 soundbar Connection - Since this speaker contains the LEFT, RIGHT and
CENTER channels, connect each one of these channels from your amplifier as
above to the designated “Left”, “Right” and “Center” terminals on the G-42.
Make sure that no bare wires from any of the connections touch each other or
any other terminals as this could cause a short and damage your equipment.
SPEAKER CARE AND CLEANING
Your Klipsch Gallery™ Speaker has a durable finish that should only require dry
dusting or cleaning with a dry cloth. Avoid the use of abrasive or solvent-based
cleaners and harsh detergents. The unique grille for the speaker consists of a
piece of sheer rectangular cloth with metal rods along two sides. It is held in
place by magnets imbedded in a slot on each side of the rear of the cabinet.
Carefully pull the metal rod away from one side, then the other to remove
grill. The grill is designed to be as lightweight and acoustically transparent as
possible so there is no rigid framework behind it. Because of this, it might be
necessary to “smooth” the cloth once the grill is attached to the cabinet by us-
ing two thumbs to pull the cloth taught from top to bottom (or side to side if unit
is mounted horizontally).
DIAGRAM 1
DIAGRAM 2
DIAGRAM 3
Front Left
Front Right
Back Surround
Left
Back Surround
Right
Surround
Right
Surround
Left
Speaker Hookup
Center
HDMI Out
HDMI 1 HDMI 2 HDMI 3
L
R
L
R
CD
TAPE TV DVD
Monitor
Out
Video
In
Out In In In In
CBL/SAT
Sub Pre Out
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Klipsch Gallery Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Klipsch Gallery Series in the language / languages: English, German, French, Portuguese, Spanish as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info