754095
23
Zoom out
Zoom in
Previous page
1/84
Next page
23
EN
INSTALLATION
Befor Installation (Built-in)
Remove all exterior and interior packing.
Before connecting the Wine Cooler to the power source, let it stand upright for
approximately 2 hours. This will reduce the possibility of a malfunction in the
cooling system caused by handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
The door on this appliance can be opened from either the left or the right side. The
unit is delivered with the door opening on the left side.
Installation
The appliance is designed to be built-in the kitchen cabinets.
The appliance should be positioned in a well-ventilated, dry room.
Place your Wine Cooler on a position that is strong enough to support it when it is
fully loaded. To level your Wine Cooler, adjust the front leveling legs at the bottom
of the Wine Cooler.
Locate the Wine Cooler away from direct sunlight and sources of heat (stove,
heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat
sources may increase electrical consumption. Extreme cold ambient temperatures
may also cause the unit not to perform properly.
Plug the Wine Cooler into an exclusive, easily accessible plug socket. Any
questions concerning power and/ or earthing should be directed towards a
qualied electrician or an authorized products service centre.
To prevent the appliance from heating up, ensure that an adequate ventilation gap
is retained and install a suitable thermal insulation panel. An adequate ow of air to
and from the cooling system must be ensured.
The appliance must be installed to all electrical, plumbing, water and drain
connections in
Built-in Cabinet Instructions
The wine cooler door seals the installed unit almost completely, so an air vent must be
provided in the base of the housing. Warmed air must be conducted via the ventilation
shaft to the rear wall of the housing and then expelled upwards. The ventilation channels
should measure at least 200 square centimeters in cross-section.
1. Remove the door gasket on the side you wish to install the handle - you can see two
designated holes for handle installation.
2. Install the handle tightly as shown above with two screws, lock washers and at
washers provided. WARN- ING: To ensure the proper functioning of the appliance,
air vents should never be blocked or covered.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Klarstein Vinsider 10035103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Klarstein Vinsider 10035103 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info