Manual Klarstein 10033109 Antarctica (page 20 of 64) (English, German, French, Italian, Spanish)

753563

Zoom out

Zoom in

1/64

OPERATION

1. Plug in the power, click the ice machine key, the ice maker starts running.

2. The supply electrovalve will open and the water level oat will oating with water ,

when the water reach the required water level the supply electrovalve will turn off,

and the machine will start the cleaning process , after cleaning completed it enter

the ice making process automatically .

3. When the ice thickness reaches the set thickness, the ice-free program starts,

the solenoid valve starts to work, the pump stops working, the heat enters the

evaporator, and the ice falls about 1.5 minutes. When the ice falls the dam-board

will turn over and turn on the magnetic reed switch .When the magnetic reed switch

closed the machine will start the ice making again. When the reed switch is closed,

the machine enters the ice making process again.

4. The compressor will not stop during the ice making and ice removing process.

5. When the ice bucket full of ice, the reed switch can not be automatically closed,

the machine automatically stops working, when taking enough ice, reed switch re-

closed, the delay after 3 minutes the machine starts, re-enter the ice process.

Ice thickness adjustment

1. Press and hold the (+) button for 3 seconds to enter the settings. When the

temperature indicator ashes, use the (+) or (-) button to adjust the thickness of the

ice. Then press the (+) button to display the number of minutes. Each time you press

(+) again, the time is increased by 1 minute. The maximum time that can be set is

25 minutes in addition to the preset ice preparation time. The time is reduced by 1

minute each time the (-) button is pressed again. The maximum time that can be set

is -9 minutes and is subtracted from the preset ice preparation time. Increase the

time for thicker ice cubes and reduce it for thin ice cubes.

2. When the ice has been discarded and the new cycle starts, the values you have just

set are automatically taken over.

Switching the light on/off

Press and hold the - button for 3 seconds to turn on the lights and press the button to turn

off the lights again for 3 seconds.

Planned switch-on

1. In standby mode, press the TIMING button. „Timed“ lights up and the remaining

time until power on is displayed in hours.

2. Press the +/ - buttons to adjust the remaining time until power is turned on.

3. Press the TIMING button again to deactivate the scheduled power-on.

The Antarctica ice maker is making a few chucks fo ice and then the maker fills with just water....please advise
Submitted on 6-7-2022 at 12:52
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Klarstein 10033109 Antarctica in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Klarstein 10033109 Antarctica Manual

Product: