777736
47
Zoom out
Zoom in
Previous page
1/120
Next page
47
EN
1. Start with the Upper Cable (67)
(a) With Upper Cable (67) in groove of Pulley (56), thread Upper Cable (67) through Upper Cross Beam (18).
(b) Install Pulley No.1 (56) to Upper Cross Beam (18), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one
M10 Nylon Nut (117).
(c) Install Pulley No.2 (56) and two Pulley Bushings (small) (89) to Support Frame (6), using one M10X70mm Hex Bolt (100), two
M10 Washers (112) and one M10 Nylon Nut (117).
(d) Install Pulley No.4 (56) to Upper Cross Beam (18), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one
M10 Nylon Nut (117).
(e) Attach the bolt end of Upper Cable (67) to Selector Shaft (5) with Plastic Washer (71).
(f) Install Pulley No.3 (56) to Pulley U (40), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10 Nylon
Nut (117).
(g) Attach Lat Bar (17) to the other end of Upper Cable (67), using one Pothook (58).
2. Assembly the Buttery Cable (68)
(a) Attach both ends of Buttery Cable (68) to Right & Left Buttery Arm (11&12), using two Plastic Covers (92).
(b) Install Pulley No.5&7 (56) to two Single Pulley Blocks (41), using two M10X45mm Hex Bolts (102), four M10 Washers (112)
and two M10 Nylon Nuts (117).
(c) Install Pulley No.6 (56) to Reverse U (39), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10 Nylon
Nut (117).
3. Assembly the Lower Cable (69)
(a) With the Lower Cable (69) in groove of Pulley (56) through Leg Extension Frame (8).
(b) Install Pulley No.8 (56) and two Pulley Bushings (small) (89) to Leg Extension Frame (8), using one M10X70mm Hex Bolt
(100), two M10 Washers (112) and one M10 Nylon Nut (117).
(c) Install Pulley No.9 (56) and two Pulley Bushings (small) (89) to Support Frame (6), using one M10X70mm Hex Bolt (100), two
M10 Washers (112) and one M10 Nylon Nut (117).
(d) Install Pulley No.10 (56) to Reverse U (39), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10
Nylon Nut (117).
(e) Install Pulley No.11 (56) to Base Frame (1), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10
Nylon Nut (117).
(f) Install Pulley No.12 (56) to Pulley U (40), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10 Nylon
Nut (117).
(g) Install Pulley No.13 (56) to Leg Press Base Frame (2), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one
M10 Nylon Nut (117).
(h) Install Pulley No.14 (56) and two Pulley Bushings (small) (89) to Leg Press Lower Support Frame (19), using one M10X70mm
Hex Bolt (100), two M10 Washers (112) and one M10 Nylon Nut (117).
(i) Install Pulley No.15 (56) to Rear Leg Press Upright Frame (24), using one M10X45mm Hex Bolt (102), two M10 Washers
(112) and one M10 Nylon Nut (117).
(j) Attach the bolt end of Lower Cable (69) to Leg Press Seat Support Frame (22), using one Pothook (58), one Short Chain (63),
one M8X40mm Hex Bolt (107), two M8 Washers (114) and one M8 Nylon Nut (118).
(k) Attach Low Bar (16) or Ankle Strap (74) to the other end of Lower Cable (69), using one Long Chain (62) and two Pothooks
(58).
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Klarfit 10033571 Ultimate Gym 9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Klarfit 10033571 Ultimate Gym 9000 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 8.86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info