784443

KKT Kolbe INTEGRA606 Manual

28
Zoom out
Zoom in
Previous page
1/64
Next page
28
Montage
Hinweis: Bei der Montage von Rückstauklappen bzw. eines Rückschlagventils ist darauf
zu achten, dass diese sich frei önen können. Ansonsten kann sich die Saugleistung redu-
zieren und das Betriebsgeräusch der Dunstabzugshaube erhöhen.
Hinweis: Wenn die Dunstabzugshaube im Umlubetrieb verwendet wird, ohne nach
außen zu entlüen, ist es wichtig, dass der Luauslass nicht blockiert wird, da sonst die
Dunstabzugshaube beschädigt wird, die Kapazität reduziert werden kann und sich das
Betriebsgeräusch erhöht.
Weiter ist zu beachten, dass kein Rückschlagventil installiert werden kann.
Hinweis: Nach der Einstellung müssen
die beiliegenden Stecker in den Schrau-
benlöchern montiert werden, um Lärm-
belästigung zu vermeiden.
3
The range hood must be pushed up until the mountings ”click”�over the construction the
range hood is to be mounted in.
If the mountings does not ”click”�they can be pushed in place, b y pressing on the screws
that holds the mountings.�This is done by pushing through the four holes in the corners of
the range hood with a screwdriver.
Note:�when mounting in a horizontal division recommends that the range hood
is insulated to avoid noise nuisance.
Click!
4x
Click!
Ceiling
Range hood
Mounting
4x
4
Adjust the mountings until the edge of the
range hood is level to the ceiling.�This is
done using a Philips screwdriver through the
four holes in the corners of the range hood.
NOTE:�After the adjustment the enclosed
plugs must be mounted in the screw
holes.�Otherwise noise nuisance can be
experienced.
The vent pipe must be mounted after the adjustment of the range hood.�Thermex
recommends that a back valve is mounted on the vent installation to prevent draft
through the vent.�When installing an external motor from Thermex the none-return valve
is placed by the motor.
5
6
3
The range hood must be pushed up until the mountings ”click”�over the construction the
range hood is to be mounted in.
If the mountings does not ”click”�they can be pushed in place, b y pressing on the screws
that holds the mountings.�This is done by pushing through the four holes in the corners of
the range hood with a screwdriver.
Note:�when mounting in a horizontal division recommends that the range hood
is insulated to avoid noise nuisance.
Click!
4x
Click!
Ceiling
Range hood
Mounting
4x
4
Adjust the mountings until the edge of the
range hood is level to the ceiling.�This is
done using a Philips screwdriver through the
four holes in the corners of the range hood.
NOTE:�After the adjustment the enclosed
plugs must be mounted in the screw
holes.�Otherwise noise nuisance can be
experienced.
The vent pipe must be mounted after the adjustment of the range hood.�Thermex
recommends that a back valve is mounted on the vent installation to prevent draft
through the vent.�When installing an external motor from Thermex the none-return valve
is placed by the motor.
5
6
Drücken Sie die Halterungen soweit ein,
bis die Kanten der Dunstabzugshaube mit
der Decke eben abschließen. Benutzen
Sie dazu einen Schraubendreher, den Sie
durch die vier Ecklöcher schieben, wie
zuvor beschrieben.
3
The range hood must be pushed up until the mountings ”click”�over the construction the
range hood is to be mounted in.
If the mountings does not ”click”�they can be pushed in place, b y pressing on the screws
that holds the mountings.�This is done by pushing through the four holes in the corners of
the range hood with a screwdriver.
Note:�when mounting in a horizontal division recommends that the range hood
is insulated to avoid noise nuisance.
Click!
4x
Click!
Ceiling
Range hood
Mounting
4x
4
Adjust the mountings until the edge of the
range hood is level to the ceiling.�This is
done using a Philips screwdriver through the
four holes in the corners of the range hood.
NOTE:�After the adjustment the enclosed
plugs must be mounted in the screw
holes.�Otherwise noise nuisance can be
experienced.
The vent pipe must be mounted after the adjustment of the range hood.�Thermex
recommends that a back valve is mounted on the vent installation to prevent draft
through the vent.�When installing an external motor from Thermex the none-return valve
is placed by the motor.
5
6
Die Dunstabzugshaube muss so weit nach oben geschoben werden, bis die Halterungen
über der Konstruktion einrasten, in der die Dunstabzugshaube montiert werden soll,
so dass ein Klickgeräusch zu hören ist. Wenn kein „Klicken“zu hören ist, können die Halte-
rungen durch Druck auf deren Halteschrauben in die richtige Position gedrückt werden.
Dazu stoßen Sie die vier Löcher in den Ecken der Dunstabzugshaube mit einem Schrauben-
dreher durch, schieben diesen in die Löcher und drücken damit auf die Halteschrauben.
Hinweis: Bei horizontaler Montage empehlt es sich, die Dunstabzugshaube zu isolieren,
um Lärmbelästigung zu vermeiden.
Decke
Haubenkörper
Halterung
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for KKT Kolbe INTEGRA606 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of KKT Kolbe INTEGRA606 in the language / languages: English, German as an attachment in your email.

The manual is 1.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info