784440

KKT Kolbe INTEGRA110 Manual

60
Zoom out
Zoom in
Previous page
1/64
Next page
60
Mounting the hood
Note: When installing backow aps or a backow valve, make sure that they can open
freely. Otherwise, the suction power may be reduced and the operating noise of the
cooker bonnet increased.
Note: If the extractor hood is used for for recirculating air without venting to the outside,
it is important that the air outlet is not blocked, as otherwise the extractor hood will be
damaged, the capacity can be reduced and the operating noise will increase. It should
also be noted that a non-return valve cannot be installed.
3
The range hood must be pushed up until the mountings ”click”�over the construction the
range hood is to be mounted in.
If the mountings does not ”click”�they can be pushed in place, b y pressing on the screws
that holds the mountings.�This is done by pushing through the four holes in the corners of
the range hood with a screwdriver.
Note:�when mounting in a horizontal division recommends that the range hood
is insulated to avoid noise nuisance.
Click!
4x
Click!
Ceiling
Range hood
Mounting
4x
4
Adjust the mountings until the edge of the
range hood is level to the ceiling.�This is
done using a Philips screwdriver through the
four holes in the corners of the range hood.
NOTE:�After the adjustment the enclosed
plugs must be mounted in the screw
holes.�Otherwise noise nuisance can be
experienced.
The vent pipe must be mounted after the adjustment of the range hood.�Thermex
recommends that a back valve is mounted on the vent installation to prevent draft
through the vent.�When installing an external motor from Thermex the none-return valve
is placed by the motor.
5
6
3
The range hood must be pushed up until the mountings ”click”�over the construction the
range hood is to be mounted in.
If the mountings does not ”click”�they can be pushed in place, b y pressing on the screws
that holds the mountings.�This is done by pushing through the four holes in the corners of
the range hood with a screwdriver.
Note:�when mounting in a horizontal division recommends that the range hood
is insulated to avoid noise nuisance.
Click!
4x
Click!
Ceiling
Range hood
Mounting
4x
4
Adjust the mountings until the edge of the
range hood is level to the ceiling.�This is
done using a Philips screwdriver through the
four holes in the corners of the range hood.
NOTE:�After the adjustment the enclosed
plugs must be mounted in the screw
holes.�Otherwise noise nuisance can be
experienced.
The vent pipe must be mounted after the adjustment of the range hood.�Thermex
recommends that a back valve is mounted on the vent installation to prevent draft
through the vent.�When installing an external motor from Thermex the none-return valve
is placed by the motor.
5
6
3
The range hood must be pushed up until the mountings ”click”�over the construction the
range hood is to be mounted in.
If the mountings does not ”click”�they can be pushed in place, b y pressing on the screws
that holds the mountings.�This is done by pushing through the four holes in the corners of
the range hood with a screwdriver.
Note:�when mounting in a horizontal division recommends that the range hood
is insulated to avoid noise nuisance.
Click!
4x
Click!
Ceiling
Range hood
Mounting
4x
4
Adjust the mountings until the edge of the
range hood is level to the ceiling.�This is
done using a Philips screwdriver through the
four holes in the corners of the range hood.
NOTE:�After the adjustment the enclosed
plugs must be mounted in the screw
holes.�Otherwise noise nuisance can be
experienced.
The vent pipe must be mounted after the adjustment of the range hood.�Thermex
recommends that a back valve is mounted on the vent installation to prevent draft
through the vent.�When installing an external motor from Thermex the none-return valve
is placed by the motor.
5
6
The cooker hood must be pushed upwards until the brackets „click“ over the construction
in which the cooker hood is to be mounted.
If the brackets do not „click“, they can be brought into position by pressing the screws
holding the brackets. To do this, insert a screwdriver through the four holes in the corners
of the cooker hood, put it into the holes and press the holding screws.
Note: For horizontal installation, it is advisable to insulate the cooker hood to prevent the
formation of annoying noises.
ceiling
hood body
bracket
Note: Aer adjustment, the enclosed
plugs must be mounted in the screw
holes.
Otherwise, annoying noises may occur.
Adjust the brackets so that the edge of
the cooker hood is level to the ceiling.
This is done by inserting a screwdriver
trough the four holes in the corner of the
range hood as described before.
… 60 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for KKT Kolbe INTEGRA110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of KKT Kolbe INTEGRA110 in the language / languages: English, German as an attachment in your email.

The manual is 1.09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info