167676

Kicker zx 550 3 Manual

2
Zoom out
Zoom in
Previous page
1/10
Next page
Installation . . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's
chassis. Adding an additional ground wire between
the battery's negative post and the vehicle chassis
of this same gauge (or larger) is recommended.
Use a twisted pair(s) of RCA (low-level)
interconnect cable to feed the audio signal to the
amplifier. If you are using only one pair of RCA
inputs, connect the RCA cable to the AMP 1
inputs. All three (or five ZX700.5) channels will
work with a single pair of RCA input cable; the
fader will not operate. Keep the RCA cable away
from factory wiring harnesses and other power
wiring. If you need to cross this wiring, cross it at a
90 degree angle.
Only use speaker wire (high-level) inputs if your source unit does not have RCA type outputs. When
using both sets of high-level inputs for the ZX700.5, the supplied RCA dummy plugs must be inserted
into the RCA AMP 2 inputs in order for the fader to work properly. In any other configuration do not use
the RCA dummy plugs. Never use shorting plugs in any configuration. See Figure 1.
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your
amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.
See the chart below for power and
ground wire size, and fusing
recommendations.
3. Configuration The following diagrams show the most common configurations for your Kicker ZX
series amplifier.
Four (ZX700.5) / Two Channel (ZX550.3) Operation with Subwoofer These ZX amplifiers are
capable of operating into a minimum impedance of 2 ohms per channel in stereo operation and
2 ohms mono in the subwoofer channel. See Figure 3.
Bridged (Mono) Operation (ZX700.5) The ZX700.5 series amplifier is capable of operating into a
minimum impedance of 4 ohms when in bridged operation. This allows you to bridge AMP 1 to run the
“right” side and AMP 2 to run the “left” side. You will need two RCA Y-Adapters for this configuration.
Each AMP is stable down to 4 ohms in this configuration. See Figure 4.
INSTALLATION
ZX.3/ZX.5AMPLIFIER
ZX550.3 / ZX700.5
Multi-ChannelModels:
ZX.3/ZX.5SeriesAmplifier
Owner’sManual
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Amplifier Model Number:
Amplifier Serial Number:
__________________________
__________________________
__________________________
__________________________
SUB INPUT
SUB
SOURCE UNIT
killers trk7“on Top”
ModelZX550.3 Fuse60A PowerGroundWire 4GA
ModelZX700.5 Fuse90A PowerGroundWire 4GA
Remote
Turn-On
Battery
+12V
Fuse
18"
Or Less
(45cm)
24"
Or Less
(60cm)
Ground
-
+
+
-
+
-
Signal In AMP 1
Signal In AMP 2
Left Speaker AMP 1
Right Speaker AMP 1
Minimum impedance of 2 ohms in the Subwoofer Channel
and 2 ohms per channel in stereo operation of the AMPs
Signal In Subwoofer
(Optional)
+
-
+
Left Speaker AMP 2
Right Speaker AMP 2
-
Mono Speaker
Subwoofer Channel
Remote
Turn-On
Battery
+12V
Fuse
18"
Or Less
(45cm)
24"
Or Less
(60cm)
Ground
-
+
+
-
+
-
Signal In AMP 1 (Right)
Signal In AMP 2 (Left)
Mono Speaker
Subwoofer Channel
Right Speaker AMP 1
Left Speaker AMP 2
Minimum impedance of 2 ohms in the Subwoofer Channel
and 4 ohms per AMP in bridged operation
Signal In Subwoofer
(Optional)
2 3
Figure 3
Figure 4
Use only one type of signal input to the
amplifier, either RCA Cable or Speaker Wire
RCA Cable
(Low-Level)
Speaker Wire
(High-Level
Output)
Speaker Wire
(High-Level Input)
Left +
Left -
Right -
Right +
CONFIGURATION
When using both sets of high-level
(speaker wire) inputs the supplied RCA
dummy plugs must be inserted into the
RCA AMP 2 inputs in order for
the fader to work properly.
Left +
Left -
Right -
Right +
Optional RCA
Subwoofer Cable Input
Optional RCA
Subwoofer Cable Output
Figure 1
ZX700.5
SUB INPUT
SUB
SOURCE UNIT
killers trk7“on Top”
Use only one type of signal input to the
amplifier, either RCA Cable or Speaker Wire
RCA Cable
(Low-Level)
Speaker Wire
(High-Level
Output)
Speaker Wire
(High-Level Input)
Left +
Left -
Right -
Right +
Optional RCA
Subwoofer Cable
Figure 2
ZX550.3
ZX700.5
ZX700.5
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kicker zx 550 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kicker zx 550 3 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info