508870

Kicker ZX 300.1 Manual

5
Zoom out
Zoom in
Previous page
1/28
Next page
5
REMOTE BASS
A
UTO
T
U
RN
ON
+12V D
C
AUDI
O
O
FFSET
L
O
HI
INP
UT
S
PKR
+
S
PKR
-
INPUT
SENSITIVIT
Y
L
X
O
VE
R
FF HI L
OU
TP
UT
L
R
R
S
PKR
+
S
PKR
-
ZXRC* REMOTE BASS
INSTALLATION
1. mount the
metal bracket
* ZXRC included with ZX750.1 ONLY
4-conductor phone cable
back view
2. slide the housing until it snaps
into the metal bracket
Input Level: The RCA inputs on KICKER ZX amplifi ers are capable of receiving either Hi or Low-level signals
from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the
Input Level switch on the amplifi er. Refer to the wiring section of this manual for additional instructions.
Crossover Switch (ZX300.1): Use the XOVER switch on the end panel of the amplifi er to set the internal
crossover to OFF or LO. When the switch is set to OFF, a full bandwidth signal will be amplifi ed. Set the switch to
LO if you want the amplifi er’s internal crossover to serve as a low-pass fi lter. Never change the crossover
“OFF/LO” switch setting with the audio system on!
Crossover Control (ZX400.1, ZX500.1, ZX750.1): The variable crossover on the top of the amplifi er allows
you to adjust the crossover frequency from 50–200Hz. The setting for this control is subjective; 80Hz is a good
place to start.
Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to
the input level of the amplifi er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it
to 25). Next, slowly turn (clockwise) the gain on the amplifi er up until you can hear audible distortion, then turn it
down a little.
Bass Boost Switch (ZX300.1): Turn the bass boost on to increase bass by 12db at 40 Hz. If you enable the
bass boost, it may be necessary to reduce the input gain control on the amplifi er to avoid clipping.
Bass Boost Control (ZX400.1, ZX500.1, ZX750.1): The variable bass boost control on the top of the
amplifi er is designed to give you increased output, 0–18dB, at 40 Hz. The setting for this control is subjective. If
you turn it up, you must readjust the input gain control to avoid clipping the amplifi er.
Remote Bass-ZXRC (not included with ZX300.1, ZX400.1, ZX500.1): When the crossover on your
amplifi er is set to LO pass, you have the ability to control the output level of the amplifi er remotely. To mount the
ZXRC remote bass level control, simply screw the metal bracket to the chosen location, then slide the housing
onto the bracket until it snaps into place. Run the cable from the controller to the “Remote Bass” jack on the
amplifi er chassis.
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 52011 ZX 300.1 400.1 500.1 750.1 RevC.indd 5 11/5/2010 1:22:36 PM11/5/2010 1:22:36 PM
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kicker ZX 300.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kicker ZX 300.1 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info