Manual Kicker zx 200 2 (page 2 of 28) (English, German, French, Spanish)

167670

Zoom out

Zoom in

1/28

ZX AMPLIFIERS

ZX.2-SERIES AMPLIFIERS Owner’s Manual

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER ampliﬁ er. Make sure there are no items

behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open

ventilation for the ampliﬁ er. If possible, mount the ampliﬁ er in the climate-controlled passenger compartment. Drill

four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the ampliﬁ er.

Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the

ampliﬁ er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,

metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the

battery’s negative post and the vehicle chassis is recommended.

The ZX ampliﬁ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals

from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the

stereo RCA input on the end panel of the ampliﬁ er using the KICKER ZISL as shown (make sure you set the ZX

ampliﬁ er’s input level switch to “HI”). Alternatively, the signal can be delivered to the ampliﬁ er using the low-level

RCA outputs on the source unit. Set the input level switch on the end panel of the ampliﬁ er to “LO”. Either input

method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to

another ampliﬁ er or component. Keep the audio signal cable away from factory wiring harnesses and other

power wiring. If you need to cross this wiring, cross it at a 90 degree angle.

PERFORMANCE

Authorized KICKER Dealer:

Purchase Date:

Model Number:

Serial Number:

Model: ZX200.2 ZX450.2

RMS Power, all channels driven

@ 14.4V, 4Ω stereo,  1% THD+N

@ 14.4V, 2Ω stereo,  1% THD+N

@ 14.4V, 4Ω mono,  1% THD+N

70W x 2

100W x 2

200W

150W x 2

225W x 2

450W

Length 10¼” (260mm) 16¾” (425mm)

Speciﬁ cations common to all models:

Height 2-1/8” (54mm)

Width 9-5/8” (244mm)

Frequency Response ± 1dB 20Hz–20kHz

Signal-to-noise Ratio >95dB, A-weighted, re: rated power

Input Sensitivity Low Level: 125mV–5V

High Level: 250mV–10V

Selectable Electronic Crossover Variable HI, LO, or OFF (bypass) | 50–200Hz, 12dB/octave

Bass Boost Variable 0–18dB @ 40Hz

Pro Tip: To get the best performance from your new KICKER Ampliﬁ er and extend the warranty by 1 year, use

genuine KICKER accessories and wiring.

MODEL: ZX200.2 / ZX450.2

2011 ZX 200.2 450.2 RevC.indd 22011 ZX 200.2 450.2 RevC.indd 2 11/5/2010 1:06:31 PM11/5/2010 1:06:31 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kicker zx 200 2 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kicker zx 200 2 Manual

Product: