Manual Kicker IX1000.5 (page 5 of 28) (English, German, French, Spanish)

508904

Zoom out

Zoom in

1/28

OPERATION

PWR PRT

GAIN

50Hz11 200Hz0dB 18dB

X-OVER FREQBASS BOOST GAIN

50Hz11 200Hz

X-OVER FREQGAIN

50Hz 200Hz

X-OVER FREQ

XOVER

OFF HI

AMP2SUB AMP1

XOVER

OFF HI

REMOTE BASS

INPUT

LEVEL

AMP2AMP1

SUB

POWERAMP1

GNDL+ L– R+ R– REM +12V

AUTO

TURN ON

12V DC AUDIO

OFFSET

FADER

OFF

SUB

INPUT

AMP2

SUB

BRIDGED

AMP2

L+ L– R+ R–

SUB

+–

BRIDGED

Automatic Turn-On Selection: The IX series offers three different automatic turn-on modes that can be

selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the

REM terminal to have +12V out for turning on additional ampliﬁ ers.

• Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from your source unit. Run 18

gauge wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the

ampliﬁ er’s positive and negative power terminals. This is the preferred automatic turn-on method.

• DC Offset Turn-On: If Remote Turn-On is not an option, the next best setting is DC Offset. The DC Offset

mode detects a 6V DC offset from the HI-Level speaker outputs when the source unit has been turned on.

• Signal Sense Turn-On: The Audio setting is the ﬁ nal alternative for Automatic turn-on. This is a Signal Sense

turn-on method that detects the incoming audio signal from your source unit and automatically turns on the

ampliﬁ er. This turn-on method will not work properly if the input gain control is not set appropriately.

Input Level: The RCA inputs on KICKER IX ampliﬁ ers are capable of receiving either Hi or Low-level signals from

your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the Input

Level switch on the ampliﬁ er. Refer to the wiring section of this manual for additional instructions.

Fader Switch: Depress the fader switch if you are running two sets of inputs (front and rear for example) to the

ampliﬁ er. Leave the fader switch OFF if you want to drive all channels from the AMP1 input.

Sub Input: If there is a dedicated output on your source unit for a subwoofer, connect it to the RCA inputs

labeled “SUB”, and set the SUB INPUT switch to the “SUB” position (depressed). If your source unit does not

have a dedicated subwoofer output, set the SUB INPUT switch to the “AMP2” position (unpressed), and make

sure your audio source is connected to the “AMP2” RCA inputs.

Remote Bass-ZXRC: When using the remote bass level control, you have the ability to control the output level

of the sub channel remotely. To mount the ZXRC remote bass level control, simply screw the metal bracket to

the chosen location, then slide the housing onto the bracket until it snaps into place. Run the cable from the

controller to the “Remote Bass” jack on the ampliﬁ er chassis.

Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to

the input level of the ampliﬁ er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it

to 25). Next, slowly turn (clockwise) the gain on the ampliﬁ er up until you can hear audible distortion, then turn it

down a little.

Crossover Switch: Use the XOVER switch on the end panel of the ampliﬁ er to set the internal crossover to

OFF, or HI. When the switch is set to OFF, a full bandwidth signal will be ampliﬁ ed. Set the switch to HI if you

want the ampliﬁ er’s internal crossover to serve as a high-pass ﬁ lter. Never change the crossover “OFF/HI” switch

setting with the audio system on!

2011 IX 1000.5 RevF.indd 52011 IX 1000.5 RevF.indd 5 11/5/2010 12:22:25 PM11/5/2010 12:22:25 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kicker IX1000.5 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kicker IX1000.5 Manual

Product: