508909

Kicker CX600.5 Manual

6
Zoom out
Zoom in
Previous page
1/32
Next page
6
OPERATION
Automatic Turn-On Selection: The CX series offers two different automatic turn-on modes; +12V and DC
Offset.
• Remote Turn-On: Run 18 gauge wire from the Remote Turn-On Lead on your source unit to the terminal
labeled REM between the amplifi er’s positive and negative power terminals. This is the preferred automatic
turn-on method.
• DC Offset Turn-On: The DC Offset mode detects a 6V DC offset from the HI-Level speaker outputs when
the source unit has been turned on.
Input Level: The RCA inputs on KICKER CX amplifi ers are capable of receiving either Hi or Low-level signals
from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the
Input Level switch on the amplifi er. Refer to the wiring section of this manual for additional instructions.
Fader Switch: Depress the fader switch if you are running two sets of inputs (front and rear for example) to the
amplifi er. Leave the fader switch OFF if you want to drive all channels from a single stereo input.
Sub Input: If there is no dedicated output on your source unit for a subwoofer, use the SUB INPUT switch to set
your subwoofer input to either SUB INPUT or AMP INPUT 2.
Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to
the input level of the amplifi er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it
to 25). Next, slowly turn (clockwise) the gain on the amplifi er up until you can hear audible distortion, then turn it
down a little.
Bass Boost Control: The variable bass boost control on the top of the amplifi er is designed to give you
increased output, 0–12dB, at 40 Hz. The setting for this control is subjective. If you turn it up, you must readjust
the input gain control to avoid clipping the amplifi er.
Crossover Control: The variable crossovers on the side panel of the amplifi er allow you to adjust the crossover
frequency from 10–200Hz (AMPS 1 & 2) and 50–200Hz (SUB). The setting for this control is subjective; 80Hz is
a good place to start.
Remote Bass-CXRC (not included): With the CXRC remote bass level control, you have the ability to control
the output level of the amplifi er remotely. To surface-mount the CXRC remote bass level control, simply screw the
remote to the chosen location, then run the cable from the controller to the “Remote Bass” jack on the amplifi er
panel. Do NOT connect/disconnect while the amplifi er is on. Connecting the 3.5mm cable without the remote
will cause the amplifi er to output at full gain, possibly damaging your speakers. See page 5.
audio inputs
2012 CX 5-Channel Amp Rev F.indd 62012 CX 5-Channel Amp Rev F.indd 6 6/22/2012 3:08:51 PM6/22/2012 3:08:51 PM
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kicker CX600.5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kicker CX600.5 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info