508907

Kicker CX1200.1 Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
6
CXRC REMOTE BASS INSTALLATION
Surface-mount the CXRC remote
using the supplied screws.
Connect the supplied 1/8th inch [3.5mm] patch cable to the
CXRC remote and the Remote Bass jack on the amplifi er
back view
TROUBLESHOOTING
If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses, poor or
incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There are Power (PWR)
& Protection (PRT) LEDs on the side panel of your Kicker CX series amplifi er. Depending on the state of the
amplifi er and the vehicle’s charging system, the LEDs will glow either green or red. When the green LED is lit, this
indicates the amplifi er is turned on and no trouble exists.
Green LED off, no output? With a Volt Ohm Meter (VOM) check the following:
+12 volt power terminal
(should read +12V to +16V)
Remote turn-on terminal (should read +12V to +16V)
Check for reversed
power and ground connections
Ground terminal, for proper conductivity.
Green LED on, no output? Check the following:
RCA connections
Test speaker outputs with a
“known” good speaker.
Substitute source unit with a “known” good source unit.
Check for a signal in the
RCA cable feeding the amplifi er with the VOM meter set to measure “AC” voltage.
Red LED fl ickering with loud music? The red LED indicates low battery voltage. Check all the connections
in your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or replace your
vehicle’s alternator.
Red LED on, no output?
Amplifi er is very hot = thermal protection is engaged. Test for proper impedance at
the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance
and multiple speaker wiring suggestions). Also check for adequate airfl ow around the amplifi er.
Amplifi er
shuts down only while vehicle is running = voltage protection circuitry is engaged. Voltage to the amplifi er is not
within the 10–16 volt operating range. Have the vehicle’s charging and electrical system inspected.
Amplifi er
will only play at low volume levels = short circuit protection is engaged. Check for speaker wires shorted to
each other or to the vehicle chassis. Check for damaged speakers or speaker(s) operating below the minimum
recommended impedance.
No or low output?
Check the balance control on source unit
Check the RCA (or speaker input) and
speaker output connections.
Alternator noise-whining sound with engine’s RPM?
Check for damaged RCA (or speaker input) cable
Check the routing of RCA (or speaker input) cable
Check the source unit for proper grounding
Check
the gain settings and turn them down if they are set too high.
Remote cable passes audio; do not
run cable parallel to power wires.
2012 CX Mono Amps Rev I.indd 62012 CX Mono Amps Rev I.indd 6 6/22/2012 2:32:30 PM6/22/2012 2:32:30 PM
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kicker CX1200.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kicker CX1200.1 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info