772982
34
Zoom out
Zoom in
Previous page
1/82
Next page
MY20K10-02_1.0_10.11.2020 34
Operation
6.4 Error messages
The drive system monitors itself continuously and
displays a number as an error message if a known
error is detected. The system may switch off
automatically depending on the type of error.
Code Remedy
The system won't
switch on (nothing
on the display
screen)
Remove the battery from its holder and
reinsert it and plug in the connector again if
necessary.
Check the connector, contacts and contact
surfaces on the display and battery for any
dirt. Metal particles may accumulate,
particularly if the connector is magnetic.
Such particles can be difficult to remove.
Press the battery button, so that the LEDs
light up.
The battery cannot
be charged
Carefully check the charger connector and
the battery socket for any deposits. Metal
particles quickly accumulate if the connector
or socket is magnetic.
The battery cannot be charged if the ambient
temperature is <0 °C. Always charge the
battery at room temperature.
Observe the information on charging in the
charger operating instructions, particularly
the error codes.
No motor
assistance (display
in operation, motor
assistance not
available)
Remove the battery from its holder and
reinsert it. Plug the connector in again if
necessary.
Fully charge the battery once.
Turn the display downward from its holder
dock, wait about a minute and turn it back up
again.
Check that all connectors are in the right
position and check all cables for any
breakage – due to sharp kinking, for
example.
If the ambient temperature is <0 °C, the
battery cannot be charged, meaning
recovery cannot be used either.
Recovery does not
work
Is the battery charge level > 90%? Recovery
will only work if the charge level is ≤ 90%.
Is the current riding speed less than
10 km/h? Recovery is not possible below
10 km/h.
Is the current riding speed more than
40 km/h? Recovery performance is reduced
above 40 km/h.
Is the ambient temperature <0 °C? The
battery cannot be charged and cannot be
restored either at a cell temperature below
C.
The motor does not
deliver full power
The motor may have reached a high
temperature range. Power is gradually
reduced when the temperature in the
electronics is 80 °C or higher. Leave the
S pedelec to cool in the shade for about
10 minutes and then resume your ride.
As the battery voltage decreases, the power
and top speed also decrease slightly. When
the battery is almost empty, the maximum
speed can be 2-3 km/h below the level
achieved when riding with a fully charged
battery.
Table 17: List of system messages
Range seems too
short
The range depends on
»»Ride profile
»»Assistance mode
»»Tyre pressure
»»Riding performance
»»Training status
»»Total weight
»»Outside temperatures
»»Battery capacity
»»The selected trip distance
»»Charging smartphones via the display
If just one of these factors is not optimal, the
range can already be significantly reduced.
Example: If the outside temperature is 0 °C,
the range may be 30-40% less.
Code Remedy
Table 17: List of system messages
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kettler Velossi 2.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kettler Velossi 2.0 in the language / languages: English as an attachment in your email.

The manual is 7.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kettler Velossi 2.0

Kettler Velossi 2.0 User Manual - German - 83 pages

Kettler Velossi 2.0 User Manual - Dutch - 82 pages

Kettler Velossi 2.0 User Manual - French - 84 pages

Kettler Velossi 2.0 User Manual - Spanish - 85 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info