3
Assembly Instructions
GB
For Your Safety
■ Exercise should be used only for its intended purpose, i.e. for physical exercise
by adult persons.
■ Any other use of the equipment is prohibited and may be dangerous. The
manufacturer cannot be held liable for damage or injury caused by
improper use of the equipment.
■ Exercise has been designed in accordance with the latest standards of safety.
Any features which may have been a possible cause of injury have been
avoided or made as safe as possible.
■ Incorrect repairs and structural modifications (e.g. removal or replacement
of original parts) may endanger the safety of the user.
■ Damaged components may endanger your safety or reduce the lifetime of
the equipment. For this reason, worn or damaged parts should be replaced
immediately and the equipment taken out of use until this has been done.
Use only original KETTLER spare parts.
■ In case of enquiry, please contact your KETTLER dealer.
■ If the equipment is in regular use, check all its components thoroughly every
1 -2 months. Pay particular attention to the tightness of bolts and nuts.This
applies especially to the securing bolts for saddle and handelbars. The brake
tension should also be checked at regular intervals and adjusted as nec-
essary.This applies especially to the securing bolts for saddle and handelbars.
■ Instruct persons using the equipment (in particular children) on possible sources
of danger during exercising.
■ Any interference with parts of the product that are not
described within the manual may cause damage, or endanger
the person using this machine. Extensive repairs must only be
carried out by KETTLER service staff or qualified personnel
trained by KETTLER.
■ Before beginning your program of exercise, consult your doctor to ensure
that you are fit enough to use the equipment. Base your
program of
exercise on the advice given by your doctor. Incorrect or excessive exercise
may damage your health.
Before assembling or using the exercise cycle , please read the following instructions carefully. They contain important
information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a
safe place for maintenance purposes or for ordering spare parts.
Handling the equipment
■ Before using the equipment for exercise, check carefully to ensure
that it has been correctly assembled.
■ It is not recommended to use or store the apparatus in a damp room
as this may cause it to rust. Please ensure that no part of the machine
comes in contact with liquids (drinks, perspiration etc.). This may cause
corrosion.
■ The Hometrainer is designed for use by adults and children should
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the manu-
facturer cannot be held liable. If, in spite of this, children are allowed
to use the equipment, ensure that they are instructed in its proper
use and supervised accordingly.
■ The exercise cycle complies with the DIN EN 957 - 1/5, class B. It
is therefore unsuitable for therapeutic use.
■ On principle, the equipment does not require any special mainte-
nance. All bearings are pre-lubricated (further lubrication is not
required) and require little maintenance.
■ A slight production of noise at the bearing of the centrifugal mass
is due to the construction and has no negative effect upon operation.
Possibly occurring noise during reverse pedalling result from
engineering and are absolutely safe.
■ Do not use corrosive or abrasive materials to clean the equipment.
Ensure that such materials are not allowed to pollute the envi-
ronment.
■ The exercise cycle has a brake system, which require little mainte-
nance and does not require any adjusting work.
■ To operate correctly, the pulse function requires a minimum voltage
of 2,7 volts.
■ The hometrainer is dependent of revolutions per minute.
■ Please ensure that liquids or perspiration never enter the machine
or the electronics.
■ Before use, always check all screws and plug-in connections as well
as respective safety devices fit correctly.
Instructions for Assembly
■ Ensure that you have received all the parts required (see check list)
and that they are undamaged. Should you have any cause for com-
plaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings carefully and
carry out the operations in the order shown by the diagrams. The
correct sequence is given in capital letters.
■ The equipment must be assembled with due care by an adult person.
If in doubt call upon the help of a second person, if possible tech-
nically talented.
■ Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful when
assembling this machine.
■ Ensure that your working area is free of possible sources of danger,
for example don’t leave any tools lying around. Always dispose pack-
aging material in such a way that it may not cause any danger. There
is always a
risk of suffocation if children play with plastic bags!
■ The fastening material required for each assembly step is shown in
the diagram inset. Use the fastening material exactly as instructed.
The required tools are supplied with the equipment.
■ Bolt all the parts together loosely at first, and check that they have
been assembled correctly. Tighten the locknuts by hand until resis-
tance is felt,
then use spanner to finally tighten nuts com-
pletely against resistance (locking device)
. Then check that
all screw connections have been tightened firmly.
Attention: once
locknuts have been unscrewed they no longer function correctly (the
locking device is destroyed), and must be replaced.
■ To pull off the pedal arms remove cap and screw (A). Grip the pedal
arm tightly, and screw in an M12 bolt (not supplied) into the thread
(B). After a few turns you may take off the pedal arm (C).
■ For technical reasons, we reserve the right to carry out preliminary
assembly work (e.g. addition of tubing plugs).
■ Please keep original packaging of this article, so that it may be used
for transport at a later date, if necessary.
List of spare parts
When ordering spare parts, always state the full article number, spare-part
number, the quantity required and the inspection number stamped on the
back.
Example order: Art. no. 7940-900 / spare-part no. 10100030/ 2 pieces
/ inspection no......
Important: spare part prices do not include fastening material; if fastening
material (bolts, nuts, washers etc.) is required, this should be clearly stated
on the order by adding the words
„with fastening material“.
KETTLER (GB) Ltd. · Merse Road · North Moons Moat · Redditch,
Worcestershire B98 9HL · Great Britain
KETTLER International Inc. · 1355, P. B. 2747 · Virginia Beach · VA 23450
USA
http://www.kettler.net
