773010
88
Zoom out
Zoom in
Previous page
1/118
Next page
MY21K01 - 12_1.0_05.08.2020 88
Troubleshooting, fault clearance and repair
9.1.7 Other errors
9.2 Repair
Special knowledge and tools are required for
many repairs. That is why only a specialist dealer
may perform repairs such as:
Replacing tyres and rims
Replacing rims and brake linings or brake discs
Replacing and tensioning the chain.
9.2.1 Original parts and lubricants
The individual pedelec parts have been carefully
selected and matched to one other.
Only original parts and lubricants must be used for
maintenance and repair.
The constantly updated accessory approval and
parts lists are in Section 11 Documents and
Drawings.
Observe the operating instructions for the new
components.
9.2.2 Replacing the lighting
Only use components of the respective power
class for replacement.
9.2.3 Adjusting the headlight
The headlight must be set, so that its light beam
shines on the road 10 m in front of the pedelec.
9.2.4 Tyre clearance check
The tyre needs to be checked each time a
suspension fork tyre is changed to another size.
1Release pressure from the fork.
2Press fork together fully.
3Measure the gap between the top of the tyre
and the crown's lower surface. The gap must
not be less than 10 mm. If the tyre is too large,
the tyre will touch the crown's lower surface if
the fork is fully pressed together.
4Release pressure on fork and pump it up again
if it is an air suspension fork.
5Take into account the fact that the gap will be
smaller if there is a guard. Check again to
ensure that there is sufficient clearance for the
tyre.
Symptom Cause Remedy
Two beeps will sound if a
switch is pressed but the
switch cannot be
operated.
Pressed switch mode has been
deactivated.
This is not a malfunction.
Three beeps are
sounded. A fault or warning has occurred.
This occurs when a warning or an error is shown on the
display screen. Follow the instructions for the code indicated
on screen in Section 6.2 System Messages.
When you use an
electronic gear shift, you
can feel that pedal
assistance becomes
weaker when the gear is
changed.
This is because the computer sets the
pedal assistance to the optimum level.
This is not a malfunction.
A noise can be heard
after switching.
Contact your specialist dealer.
It is normal to hear a
noise coming from the
rear wheel when cycling
as normal.
The gear shift setting may not have
been made properly.
Contact your specialist dealer.
If you stop the pedelec,
gear transmission does
not switch to the position
pre-configured in the
functional feature.
You may have applied too much
pressure onto the pedals.
It is easier to change gears if you press onto the pedals gently.
Table 54: Error solution for battery
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kettler Quadriga 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kettler Quadriga 2021 in the language / languages: English as an attachment in your email.

The manual is 16.48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kettler Quadriga 2021

Kettler Quadriga 2021 User Manual - German - 125 pages

Kettler Quadriga 2021 User Manual - Dutch - 120 pages

Kettler Quadriga 2021 User Manual - French - 126 pages

Kettler Quadriga 2021 User Manual - Spanish - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info