4
Instructions for Assembly
■ Ensure that you have received all the parts required (see check list)
and that they are undamaged. Should you have any cause for com-
plaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings carefully and
carry out the operations in the order shown by the diagrams. The
correct sequence is given in capital letters.
■ The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if pos-
sible technically talented.
■ Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful
when assembling this machine.
■ Ensure that your working area is free of possible sources of danger,
for example don’t leave any tools lying around. Always dispose pack-
aging material in such a way that it may not cause any danger. There
is always a risk of suffocation if children play with plastic bags!
■ The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as instructed.
The required tools are supplied with the equipment.
■ Bolt all the parts together loosely at first, and check that they have
been assembled correctly. Tighten the locknuts by hand until resis-
tance is felt, then use spanner to finally tighten nuts com-
pletely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention:
once locknuts have been unscrewed they no longer function cor-
rectly (the locking device is destroyed), and must be replaced.
■ To pull off the pedal arms remove cap and screw (A). Grip the pedal
arm tightly, and screw in an M12 bolt (not supplied) into the thread
(B). After a few turns you may take off the pedal arm (C).
■ For technical reasons, we reserve the right to carry out preliminary
assembly work (e.g. addition of tubing plugs).
■ Please keep original packaging of this article, so that it may be used
for transport at a later date, if necessary.
■ Nobody may be in the moving range of a training person during training.
Instructions de montage
F
Pour votre sécurité
■ La bicyclette pour la mise en forme, ne doit être utilisée que pour les
fins auxquelles elle est destinée, c'est-à-dire pour l'entraînement des
adultes.
■ Tout autre emploi est interdit, voire dangereux. Le fabricant ne pourra
être rendu responsable de dommages causés par l'emploi inadéquat
de l'appareil.
Lire attentivement les présentes instructions avant le montage et la première utilisation de l'appareil. Elles contiennent des renseignements
importants relatifs à la sécurité des personnes ainsi qu'à l'emploi et à l'entretien de la bicyclette d´áppartement . Conserver soigneusement les-
dites instructions pour d'éventuels renseignements ainsi que pour effectuer l'entretien de l'appareil ou commander des pièces de rechange.
■ A slight production of noise at the bearing of the centrifugal mass
is due to the construction and has no negative effect upon ope-
ration. Possibly occurring noise during reverse pedalling result
from engineering and are absolutely safe.
■ Do not use corrosive or abrasive materials to clean the equipment.
Ensure that such materials are not allowed to pollute the envi-
ronment.
■ The exercise cycle has a magnetic brake system.
■ To operate correctly, the pulse function requires a minimum
voltage of 2,7 volts (only for computers working with batteries).
■ The equipment is dependent of revolutions per minute.
■ Please ensure that liquids or perspiration never enter
the machine or the electronics.
■ Before use, always check all screws and plug-in connections as
well as respective safety devices fit correctly.
■ Always wear suitable shoes when using.
List of spare parts page 22-23
When ordering spare parts, always state the full article number,
spare-partnumber, the quantity required and the S/N of the product
(see handling).
Example order: Art.no. 07960-700 / spare-part no. 67000170
/ 2 pieces / S/N ....................
Please keep original packaging of this article, so that it may be used
for transport at a later date, if necessary.
Goods may only be returned after prior arrangement and in
(internal) packaging, which is safe for transportation, in the original
box if possible.
It is important to provide a detailed defect description / damage
report!
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this should
be clearly stated on the order by adding the words „with fastening
material“.
Waste Disposal
KETTLER products are recyclable. At the end of its useful life please
dispose of this article correctly and safely (local refuse sites).
KETTLER (GB) Ltd.
Merse Road · North Moons Moat · Redditch,
Worcestershire B98 9HL · Great Britain
http://www.kettler.co.uk
KETTLER International Inc.
P. B. 2747 · Virginia Beach · Virginia Beach, Virginia
23450 USA
http://www.kettlerusa.com
