4
Instructions de montage
F
Pour votre sécurité
■ L’ergomètre ne doit être utilisée que pour les fins auxquelles elle est
destinée, c'est-à-dire pour l'entraînement des adultes.
■ Tout autre emploi est interdit, voire dangereux. Le fabricant ne
pourra être rendu responsable de dommages causés par l'emploi
inadéquat de l'appareil.
■ Vous vous entraînez avec un appareil dont la technique et la
sécurité correspondent aux exigences modernes. Les sources pos-
sibles de danger qui pourraient entraîner des blessures ont été soit
supprimées, soit sécurisées.
■ Les réparations inadéquates et les modifications apportées à la con-
struction de l'appareil (démontage des pièces d'origine, montage
de pièces non autorisées, etc.) peuvent entraîner des risques
imprévus pour l'utilisateur.
■ Les composants endommagés peuvent affecter votre sécurité et la
durée de vie de l'appareil. On remplacera donc sans tarder les
composants usés ou endommagés et on interdira l'emploi de l'ap-
pareil aussi longtemps qu'ils n'auront pas été remplacés. N'utiliser
que des pièces de rechange KETTLER d'origine.
Lire attentivement les présentes instructions avant le montage et la première utilisation de l'appareil. Elles contiennent des renseignements
importants relatifs à la sécurité des personnes ainsi qu'à l'emploi et à l'entretien de la bicyclette d´áppartement . Conserver soigneusement
lesdites instructions pour d'éventuels renseignements ainsi que pour effectuer l'entretien de l'appareil ou commander des pièces de rechange.
Instructions for Assembly
■ Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the
diagrams. The correct sequence is given in capital letters.
■ The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if pos-
sible technically talented.
■ Please note that there is always a danger of injury when
working with tools or doing manual work. Therefore please be
careful when assembling this machine.
■ Ensure that your working area is free of possible sources of danger,
for example don’t leave any tools lying around. Always dispose pack-
aging material in such a way that it may not cause any danger. There
is always a risk of suffocation if children play with plastic bags!
■ The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as
instructed. The required tools are supplied with the equipment.
■ Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use spanner to finally tighten nuts
completely against resistance (locking device). Then check that all
screw connections have been tightened firmly. Attention: once
locknuts have been unscrewed they no longer function correctly
(the locking device is destroyed), and must be replaced.
■ To pull off the pedal arms remove cap and screw (A). Grip the
pedal arm tightly, and screw in an M12 bolt (not supplied) into the
thread (B). After a few turns you may take off the pedal arm (C).
■ For technical reasons, we reserve the right to carry out
preliminary assembly work (e.g. addition of tubing plugs).
■ Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
List of spare parts
When ordering spare parts, always state the full article number, spare-part
number, the quantity required and the inspection number stamped on the back.
Example order: Art. no. 07983-000 / spare-part no. 10100030/ 2 pieces
/ inspection no......
Important: spare part prices do not include fastening material; if fastening material
(bolts, nuts, washers etc.) is required, this should be clearly stated on the order
by adding the words „with fastening material“.
KETTLER (GB) Ltd. · Merse Road · North Moons Moat · Redditch,
Worcestershire B98 9HL · Great Britain
KETTLER International Inc. · 1355, P. B. 2747 · Virginia Beach · VA
23450 USA
http://www.kettler.net
Handling the equipment
■ Before using the equipment for exercise, check carefully to
ensure that it has been correctly assembled.
■ It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust. Please ensure that no part of
the machine comes in contact with liquids (drinks, perspiration
etc.). This may cause corrosion.
■ The machine is designed for use by adults and children should
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the
manufacturer cannot be held liable. If, in spite of this,
children are allowed to use the equipment, ensure that they
are instructed in its proper use and supervised accordingly.
■ The exercise cycle complies with the DIN EN 957 - 1/5, class
HA. It is therefore suitable for therapeutic use.
■ Before beginning your first training session, familiarize
yourself thoroughly with all the functions and settings of the
unit.
■ A slight production of noise at the bearing of the centrifugal
mass is due to the construction and has no negative effect
upon operation. Possibly occurring noise during reverse
pedalling result from engineering and are absolutely safe.
■ The exercise cycle has a magnetic brake system.
■ The equipment is independent of revolutions per minute.
■ Please ensure that liquids or perspiration never enter the
machine or the electronics.
■ Before use, always check all screws and plug-in connections
as well as respective safety devices fit correctly.
■ Always wear suitable shoes when using.
■ Do not use corrosive or abrasive materials to clean the
equipment. Ensure that such materials are not allowed to
pollute the environment.
