605014

Kettler 07627-860 Sinto M Manual

15
Zoom out
Zoom in
Previous page
1/84
Next page
15
GB
UT6886/UT6887
• Pressing “MODE” stops and starts the display change.
• When defaults are reached for time, distance and
Kjoule/Kcal
(0-values), brief signal tones are output and the bottom display
areas flash. From now, the values count upwards again.
• If the input pulse value is exceeded, the bottom pulse display
flashes as a warning.
Interruption or End to Training
If there are fewer than 15 cadences/min, the electronics detects
that training has been interrupted. STOP SCAN is shown in the
display and the training data is displayed in rotation.
→ RPM or SPEED → TIME → DISTANCE →Kjoule/Kcal→ PULSE →
ODO → etc.
• Pressing “MODE” stops and starts the display change.
The training data is displayed for 4 minutes. If you do not press
any buttons or train in this time, the electronics switches to
standby mode and displays the time.
An interruption to training is detected with a delay of a few
seconds.
Resuming Training
If you continue the training within 4 minutes, the
last values continue counting or count downwards.
RECOVERY Recovery pulse stage
The RECOVERY function can be used after each exercise
program.
The RECOVERY button is used to initiate recovery pulse
measurement at the end of exercising. Initial and final pulse
during one minute are used to calculate deviation and a fit-
ness score. In case of equal exercising, improvement of such
score is a measurement for increase of fitness.
When reaching the target values, end exercising and press
the RECOVERY button; then, leave your hands at the hand
pulse sensors. In case of previous pulse measurement, the
display shows 00:60 for time, and the PULSE display shows
the current pulse value (flashing). The countdown starts at
00:60. Leave your hands at the hand pulse sensors until the
countdown reaches >0<. The display will show on its right a
value between F1 and F6. F1 is the best status; F6 is the
worst status. The function can be ended by pressing again
RECOVERY.
If no pulse is measured in the beginning or at the end of the
reverse counting, the error message “Err” is displayed.
Comment:
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kettler 07627-860 Sinto M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kettler 07627-860 Sinto M in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kettler 07627-860 Sinto M

Kettler 07627-860 Sinto M Installation Guide - English, German, Dutch, Danish, French, Italian, Portuguese, Spanish - 36 pages

Kettler 07627-860 Sinto M Installation Guide - All languages - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info