730373
64
Zoom out
Zoom in
Previous page
1/72
Next page
64
Knowledge
÷ Connect properly referring to “System con-
nection”.
÷ Switch MUTE OFF.
÷ Unplug the headphone plug.
÷ Connect properly referring to “System con-
nection”.
÷ This is not malfunction. Press the DISPLAY/
DEMO key to cancel the demonstration.
÷ Adjust the present time again.
÷ Adjust the present time again.
÷ Adjust the present time referring to “Clock
adjustment”.
÷ Set the timer ON time and OFF time.
÷ Execute the timer program.
÷ Connect antennas.
÷ Select a band.
÷ Tune to the frequency of the desired sta-
tion.
÷ Install the outdoor antenna in an apart posi-
tion from the road.
÷ Switch the suspected electric appliance OFF.
÷ Install the TV or the system at an increased
distance between them.
÷ Preset stations with tunable frequencies.
÷ Preset stations again.
÷ Check the speaker connection.
÷ Set the surround speaker switch on the
rear of the unit to ON.
÷ The speaker cords are disconnected.
÷ The MUTE switch of remote control unit is
switched ON.
÷ The headphone plug is inserted into the
jack.
÷ The speaker cords are disconnected.
÷ The DEMO is set to on.
÷ There was a power failure.
÷ The power cord was unplugged from the
outlet.
÷ The present time has not been adjusted or
there was a power failure.
÷ The timer ON time and OFF time have not
been set.
÷ The timer execution was not set up.
÷ The antennas have not been connected.
÷ A proper broadcasting band has not been
selected.
÷ The frequency of the station to be received
is not tuned.
÷ Car ignition noise.
÷ Influence of an electric appliance.
÷ A TV set is installed near the system.
÷ The frequency of the preset station is not
tunable.
÷ The preset memory has been cleared be-
cause the power cord has been unplugged
for a long period.
÷ The speaker connection is abnormal.
÷ The surround speaker switch on the rear of
the unit is set to OFF.
What seems to be a malfunction is not always so. Before calling for service, check the following table according to the symptom
of your trouble.
Operation to reset
The microcomputer may fall into malfunction (impossibility
to operate, erroneous display, etc.) when the power cord is
unplugged while power is ON or due to an external factor. In
this case, execute the following procedure to reset the
microcomputer and return it to normal condition.
÷ Please note that resetting the microcomputer clears the
contents stored in and returns and to condition when it left
the factory.
Sound is not produced.
Sound is not produced from the left
or right speakers.
Demonstration starts suddenly.
The clock display is out of order.
Timer operation is not possible.
Radio stations cannot be received.
Noise interferes.
A station has been preset but it can-
not be received by pressing the
P.CALL key.
The STANDBY indicator flashes red.
No sound from the surround speak-
ers (Only XD-DV70/XD-DV60/XD-
DV50/XD-A850DV)
RemedyCauseSymptom
Receiver, speakers
!
&
&
!
3
^
^
^
Q
Q
0
0
In case of difficulty
Set the POWE key to ON. Then press the VIDEO/
AUX key while holding the TUNING MODE key
down.
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood XD-DV70 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood XD-DV70 in the language / languages: English as an attachment in your email.

The manual is 3,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info