446106
20
Zoom out
Zoom in
Previous page
1/72
Next page
XD-SERIES (EN/M,T)
20
Preparation section
Operation of remote control unit
Loading batteries
1 Remove the cover. 3 Close the cover.
÷ Insert two R6 (“AA”-size) batteries
following the polarity indications.
2 Insert batteries.
Operation
Plug the power cord into the mains power outlet and
press the on/standby (
POWER) key of the remote
control unit to turn power ON. After the power has been
turned ON, press the desired key.
To turn power off, press the on/standby( POWER) key
again.
The power mode enters the STANDBY mode in which
the “STANDBY” indicator lights up. (The “TIMER” in-
dicator also lights in this mode if a timer program has
been activated.)
÷ When pressing more than one remote control keys
successively, press the keys securely by leaving an
interval of 1 second or more between keys.
1.The provided batteries are intended for use in operation checking, and their service life may be short.
2.When the remote controllable distance becomes short, replace both of the batteries with new ones.
3.If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote
sensor, malfunction may occur. In such a case, change the installation position to avoid malfunction.
Operating range
(approx.)
Remote sensor
2
1
Notes
Notes
CHANNEL
SPACE freq.
Area
1
2
USA, Canada and South
American countries
Other countries
FM : 100 kHz
AM : 10 kHz
FM : 50 kHz
AM : 9 kHz
The space between radio channels has been set to the
one that prevails in the area to which the system is
shipped. However, if the current channel space setting
does not match the setting in the area where the sys-
tem is to be used, for instance when you move from
area 1 or area 2 shown in the following table or vice
versa, proper reception of AM/FM (MW/FM) broad-
casts cannot be expected. In this case, change the chan-
nel space setting in accordance with your area by re-
ferring to the following table.
CHANNEL SPACE setting
(Except for the U.S.A., Canada, U.K., Europe, Australia and Russia)
1 Select the TUNER input.
2 While holding the SELECT key depressed, turn
the SOUND CONTROL jog dial to select the
system mode.
ENTER
F0M100/AM1
F9M 50/AM
SELECT
30
˚
6m
30
˚
÷ The “AM” display is variable depending on the model
(country or area), and “MW” may be displayed in
some areas.
1 “FM100/AM10 kHz” STEP,
2 “FM 50 /AM 9 kHz” STEP,
3 Establish the selection.
S
O
U
N
D
C
O
N
T
R
O
L
XD-6...series
XD-8...series
XD-7...series
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood xd-702 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood xd-702 in the language / languages: English as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info