158519
56
Zoom out
Zoom in
Previous page
1/60
Next page
XD-750/700/550/500 (En)
56
Preparation sectionBasic sectionApplication sectionKnowledge sections
In case of difficulty
Remote control unit
Symptom Cause Remedy
Remote control operation is not possible.
RemedyCauseSymptom
Receiver, speakers
÷ Connect properly referring to “System con-
nection”.
÷ Adjust to an required volume.
÷Switch MUTE OFF.
÷Unplug the headphone plug.
÷Turn the power OFF, remove the short-
circuit and turn the power ON again.
÷Connect properly referring to “System con-
nection”.
÷ Adjust the present time again.
÷Adjust the present time again.
÷Adjust the present time referring to “Clock
adjustment”.
÷Set the timer ON time and OFF time.
÷Execute the timer program with the SRS
3D (SOURCE DIRECT)* key.
÷Connect antennas.
÷Select a band.
÷Tune to the frequency of the desired sta-
tion.
÷Install the outdoor antenna in an apart posi-
tion from the road.
÷Switch the suspected electric appliance
OFF.
÷Install the TV or the system at an increased
distance between them.
Sound is not produced.
The character display blinks and sound is
not produced.
Sound is not produced from the left or
right speakers.
The clock display blinks without chang-
ing the figures.
Timer operation is not possible.
Radio stations cannot be received.
Noise interferes.
÷The speaker cords are disconnected.
÷The volume control is set to the minimum
position.
÷The MUTE switch of remote control unit is
switched ON.
÷The headphone plug is inserted into the
jack.
÷The speaker cords are short-circuited.
÷The speaker cords are disconnected.
÷There was a power failure.
÷The power cord was unplugged from the
outlet.
÷The present time has not been adjusted or
there was a power failure.
÷The timer ON time and OFF time have not
been set.
÷The timer execution was not set up.
÷The antennas have not been connected.
÷A proper broadcasting band has not been
selected.
÷The frequency of the station to be received
is not tuned.
÷Car ignition noise.
÷Influence of an electric appliance.
÷A TV set is installed near the system.
÷Batteries are exhausted.
÷The remote control is too far away from the
system, the controlling angle is deviated or
there is an obstacle in between.
÷There is no tape or CD set in the component
to be played.
÷An attempt is made to play the cassette
deck which is recording something.
÷Replace with new batteries.
÷Operate the unit inside the remote control-
lable range.
÷Set a tape or CD in the component to be
played.
÷Wait until the recording ends.
$
$
6
^
&
&
6
6
p
p
p
W
E
6
¢
¢
9
What seems to be a malfunction is not always so. Before calling for service, check the following table according to the
symptom of your trouble.
Operation to reset
The microcomputer may fall into malfunction (impossibility to
operate, erroneous display, etc.) when the power cord is un-
plugged while power is ON or due to an external factor. In this
case, execute the following procedure to reset the microcom-
puter and return it to normal condition.
÷Please note that resetting the microcomputer clears the contents
stored in and returns and to condition when it left the factory.
Reset using a sharp-tipped object.
RESET
∞
* The key inside ( ) is used only with the XD-550/XD-500.
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood xd 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood xd 500 in the language / languages: English as an attachment in your email.

The manual is 2,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info