683161
190
Zoom out
Zoom in
Previous page
1/196
Next page
ID Message Description/Corrective Action
0049
The storage location cannot be changed while a PSK QSO log
recording. (ERR: 0049)
Appears when attempting to change the destination for saving the file
while PSK communication log recording is in progress.
004D
Audio files cannot be copied while an audio recording. (ERR:
004D)
Appears when attempting to copy files to a PC or USB while manual
recording is in progress.
004E
Communication log files (CW) cannot be copied while a CW QSO
log recording. (ERR: 004E)
Appears when attempting to copy files to a PC or USB while CW
communication log recording is in progress.
004F
Communication log files (RTTY) cannot be copied while a RTTY
QSO log recording. (ERR: 004F)
Appears when attempting to copy files to a PC or USB while RTTY
communication log recording is in progress.
0050
Communication log files (PSK) cannot be copied while a PSK
QSO log recording. (ERR: 0050)
Appears when attempting to copy files to a PC or USB while PSK
communication log recording is in progress.
0051
KNS log files cannot be copied while a KNS log recording. (ERR:
0051)
Appears when attempting to copy files to a PC or USB while KNS log
recording is in progress.
0055
Audio files cannot be deleted while an audio recording. (ERR:
0055)
Appears when attempting to delete files while manual recording is in
progress.
0056
Communication log files (CW) cannot be deleted while a CW QSO
log recording. (ERR: 0056)
Appears when attempting to delete files while CW communication log
recording is in progress.
0057
Communication log files (RTTY) cannot be deleted while a RTTY
QSO log recording. (ERR: 0057)
Appears when attempting to delete files while RTTY communication log
recording is in progress.
0058
Communication log files (PSK) cannot be deleted while a PSK
QSO log recording. (ERR: 0058)
Appears when attempting to delete files while PSK communication log
recording is in progress.
0059
KNS log file cannot be deleted while a KNS log recording. (ERR:
0059)
Appears when attempting to delete files while KNS log recording is in
progress.
005B
Copying was aborted due to the number of files exceeded 255 in
the destination folder. (ERR: 005B)
Reduce the number of files in UBS flash drive and then copy again.
Appears when the number of files at the copy destination has exceeded
the maximum limit of 255 files while copy is in progress.
005C
The selected file cannot be read because the market code is
different. (ERR: 005C)
The transceiver type does not match the transceiver type that created
the settings data file.
0103
The current sourced from the USB connector exceeds the upper
limit value. (ERR: 0103)
Remove the USB device and then restart the transceiver.
Appears when overcurrent is detected at the USB connector.
Disconnect unused USB devices.
0105
PLL unlock was detected. (ERR: 0105)
Refer to "Troubleshooting" in the instruction manual.
Perform Full Reset. If PLL unlock is still detected after Full Reset, note
down the error message number (ERR:0105) and send an inquiry to
KENWOOD service center.
0107
No reference signal has been detected. (ERR: 0107)
Ensure that the reference signal has been sourced to the REF IN
(10 MHz) connector.
Appears when there is no reference signal input from an external source.
Check whether there is signal input to the REF IN terminal and whether
the level of the signal is high enough.
0109
Corruption of the data was detected. (ERR: 0109)
Executing the Full Reset will initialize the transceiver to the
defaults.
Press [OK] (F) to start the Full Reset.
Appears when damage is found in the backup data.
Press F [OK] to perform Full Reset.
010A to
010F,
0110 to
0115
A DSP error was detected. (ERR: 010A to 010F, 0110 to 0115)
Refer to "Troubleshooting" in the instruction manual.
Perform Full Reset.
If the same error message appears again after Full Reset, note down
the error message number (ERR: 010A to 010F, 0110 to 0115) and send
an inquiry to KENWOOD service center.
0117
A hardware error was detected. (ERR: 0117)
Refer to "Troubleshooting" in the instruction manual.
Perform Full Reset.
If the same error message appears again after Full Reset, note down
the error message number (ERR:0117) and send an inquiry to
KENWOOD service center.
Turn off the power of the regulated DC power supply after “A system error has occurred.” message is displayed.
If error occurs frequently, try updating to the latest firmware. If the same problem persists, this transceiver could be faulty.
Please contact KENWOOD service center.
18 TROUBLESHOOTING
18-10
190


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info