683161
136
Zoom out
Zoom in
Previous page
1/196
Next page
Operation on
This
Transceiver
Key Operation Content of Voice Guidance
Switching of
quick memory
channel
Turn
[MULTI/CH]
Simplex mode:
Quick + Number + [A/ B]
*1
Frequency + ([X/ R/ XR] + RIT/XIT
Frequency)
*2
Split mode:
Quick + Number + Split + [A/
B]
*1
Frequency + ([X/ R/ XR] +
RIT/XIT Frequency)
*2
Entering a
frequency using
the numeric
keypad
[ENT]
Enter
Entering a
channel number
using the
numeric keypad
Press a key on
the numeric
keypad
Numeric value that is entered
Switching the
frequency entry
history
Turn
[MULTI/CH]
Frequency entry history
Switching
frequency lock
[LOCK]
Lock + [On/ Off]
Switching split
operation
[SPLIT]
Split + [On/ Off]
Configuring split
frequency via
numeric keypad
operation
Press and hold
[SPLIT]
Split + Enter
When [0] is first
pressed
Minus
Numeric keypad
TX + [Plus/ Minus]
*
+ Numeric
value that is entered + Kilohertz
* Pressing the keys from [1] to [9]
adds a Plus utterance, while
pressing [0] + ([1] to [9]) adds a
Minus utterance.
When
configuration of
the split
frequency using
the Tuning
control is
complete
[SPLIT] (After
configuration
using the
Tuning control)
TX + Finalized TX frequency
Changing the
low cutoff
frequency
Turn [LO/
WIDTH]
Low + Frequency
Changing the
width
Turn [LO/
WIDTH]
Width + Options
Changing the
high cutoff
frequency
Turn [HI/SHIFT]
High + Options
Changing the
shift frequency
Turn [HI/SHIFT]
Shift + Options
Changing the TX
output power
Turn [POWER]
When drive output is ON: TX
power + Value
When drive output is OFF:
When the transverter is ON and TX
Power Down with Transverter
Enabled is “On”: TX power + 5
In all other cases: TX power +
Value (The value shows a value up
to the TX output power limit if the TX
output power limiter is operating.)
[MIC/PITCH]
control
operation
Turn [MIC/
PITCH]
When adjusting microphone
gain: Mic. Gain + Value
When adjusting the speech
processor output level:
Processor+ Out + Value
* No voice is output during
adjustment of the sidetone/pitch
frequency.
Operation on
This
Transceiver
Key Operation Content of Voice Guidance
[DELAY] control
operation
Turn [DELAY]
When adjusting the break-in
delay time: Full + Break-in in
the case of FULL-BK
DELAY: Break-in delay +
Displayed value in the case of 1 to
20
When adjusting VOX delay:
VOX delay + Value
[KEY] control
operation
Turn [KEY]
When adjusting the keying
speed: Keying speed + Value
Timer function
ON/OFF
operation
F [TIMER]
Timer + [On/ Off]
Dimmer
switching
F [DIMMER]
F2 [DIMMER]
D + Numeric value (single digit)
Antenna
switching
F [ANT]
Antenna + Number
Band Direct
selection
Band Direct
keys (including
operation of
[GENE])
Frequency
Calling up the
preconfigured
emergency
frequency
PF [Emergency
Frequency]
Emergency + Frequency
Meter switching F [METER]
Analog meter display (TX digital
meter OFF): [Power/ SWR/ ID/
Processor/ ALC/ VD]
Analog meter display (TX digital
meter ON): [SWR/ ID/ Processor/
VD/ TMP]
Digital meter display: [SWR/ ID/
Processor/ VD/ TMP]
Mini digital meter display: [Power/
SWR/ ID/ Processor/ ALC/ VD/
TMP]
Error/warning
messages
(none)
Error or warning + Number
* For more details on the number,
please refer to “Error Messages
(18-9) and “Warning Messages
(18-11).
Voice 1
Voice 1 announces the displayed frequency, channel number,
details of the respective configuration modes as well as the status
of menu settings.
Announces the digits of the VFO and memory channel frequencies
which are higher than 10 Hz when fine tuning is OFF. “Point” is
uttered after announcing the MHz digits. When a channel that does
not contain any operating data is selected during memory scroll,
“Blank” is uttered.
Press the PF key that is assigned with “VOICE1”.
Announces the operating status. Announces the setting value
while configuration is in progress on the configuration screen.
Pressing the PF key that is assigned with “VOICE1”,
“VOICE2” or “VOICE3” during the announcement stops
the announcement.
Altering the frequency by turning the Tuning or [MULTI/
CH] control during an announcement stops the
announcement.
For more details on how to change the assignment of PF
keys, please refer to “PF Keys (Programmable Function
Keys)” (16-2).
Announcement is not output while scanning is in
progress.
13 VOICE GUIDANCE
13-2
136


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info