683161
99
Zoom out
Zoom in
Previous page
1/196
Next page
Switching the Scope Display Mode
1
Display the bandscope screen.
2
Press F2 [S.MODE].
If F2 [S.MODE] is not displayed, press F1 [MORE] to display
F2 [S.MODE].
Pressing F2 [S.MODE] each time switches the selection to
“Auto Scroll Mode”, “Fixed Mode” and “Center Mode” in
sequence.
Auto Scroll Mode (AUTO SCROLL MODE)
Moves the marker of the tuning frequency to within the scope
range. If the lower or upper limit of the display range is
exceeded, the scope range is automatically scrolled by half a
screen.
Fixed Mode (FIXED MODE)
Moves the marker of the tuning frequency to within the scope
range preconfigured for each amateur band. Up to 3 scope
ranges can be preconfigured for one amateur band.
Center Mode (CENTER MODE)
The marker of the tuning frequency is normally fixed at the
center.
Auto Scroll Mode
.
Fixed Mode
.
Center Mode
.
Switching the Display Frequency Span
When the bandscope is displayed in the Auto Scroll mode or
Center mode, the display frequency span (the width between the
lower and upper frequency limits in the bandscope screen) can be
adjusted.
Press F3 [SPAN].
If F3 [SPAN] is not displayed, press F [MORE] to display F3
[SPAN].
Pressing F3[SPAN] each time switches the frequency span.
Setting Value
5kHz/ 10kHz/ 20kHz/ 30kHz/ 50kHz/ 100kHz/
200kHz/ 500kHz
The display frequency span can be configured separately for
audio mode (SSB/AM/FM (including DATA mode)) and non-
audio mode (CW/FSK/PSK).
The default settings of the audio mode and non-audio mode
are “50Hz (± 25Hz)” and “10kHz (± 5Hz)” respectively.
Pressing and holding F3[SPAN] each time switches the
options in the reverse sequence.
The selected display frequency span is displayed in the
toolbar of the bandscope screen as “SPAN 50kHz”, for
example.
Marker Shift
This function shifts the scope range in the auto scroll mode
operation so that the marker is displayed at an easy to observe
position.
Shifting the Marker
Press F4 [SHIFT].
If F4 [SHIFT] is not displayed, press F [MORE] to display
F4 [SHIFT].
The marker shifts close to the preset shift position (default value
is center).
Depending on the relationship between the RX
frequency and the span, deviation of 1 grid to the left or
right may occurred in the shift operation.
Changing the Shift Position of Marker Shift
1
Press and hold F4 [SHIFT].
If F4 [SHIFT] is not displayed, press F [MORE] to display
F4 [SHIFT].
The transceiver enters the shift position configuration mode.
The value indicating the position of the selected vertical grid
line is displayed.
2
Move the shift position to the desired position using
the [MULTI/CH] control.
Pressing and holding F4 [SHIFT] moves the shift position to
the center.
3
Press F4 [SHIFT].
The transceiver exits the shift position configuration mode.
When observing the condition of the frequency calling
the DX station or the condition in the RX passband during
digital communication such as FT8, change the shift
position of the marker to display the RX frequency
marker at the edge. Doing so widens the width for
displaying the signal compared to when the marker is
near the center.
SCOPE FUNCTIONS 7
7-3
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info