683161
93
Zoom out
Zoom in
Previous page
1/196
Next page
NB2
NB2 is a function for blanking pulse noise with a long pulse width
which cannot be blanked by NB1. NB2 is further divided into Type
A and Type B, which can be employed according to the
circumstances. NB2 can also be used together with NB1.
Type A
.
Type A suppresses mainly the pulse noise
without blanking the target signal. The level
of the effect (Level) can be adjusted.
Type A
Target Signal
Pulse Noise
As pulse noise remains after blanking when “Type A” is
used, pulse noise might be audible when the target
signal is strong or when there is strong interference
within the passband. Even in such a situation, it has the
effect of bringing up the target signal when AGC gain is
low due to pulse noise.
“Type A” is most effective in cases where weak target
signals are buried in strong pulse noise.
Type B
.
Target Signal
Pulse Noise As with NB1, Type B blanks the pulse noise
together with target signal. The pulse
sensitivity level (Level), blanking duration
(Width) and attenuation level (Depth) can
be adjusted.
Type B
When pulse noise with a long pulse width is blanked using
“Type B”, the time interval for which the target signal is
removed becomes longer due to the long blanking time,
and this causes the silence period to stand out.
1 Press and hold [NB2] to display the Noise Blanker
2 configuration screen.
2 Press F6 [TYPE].
Pressing F6 [TYPE] each time toggles the screen between
“Type A” and “Type B”.
Type A Screen
.
Type B Screen
.
3 Press and hold [NB2] or press [ESC] to end the
process.
Pressing and holding [NB2] displays the noise blanker
2 screen which shows the current type in use.
The default setting is “Type A”.
Type selection can be configured separately for audio
mode (SSB/AM (including DATA mode)) and non-audio
mode (CW/FSK/PSK).
Configuring the NB2 Effect Level (Type A)/ NB2 Pulse
Sensitivity Level (Type B)
1 Press and hold [NB2] to display the Noise Blanker
2 configuration screen.
2 While the Type B screen is displayed, press F2
[ ]/ F3 [ ] to select “Level”.
3 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to change the level.
Setting Value 1 to 6 (default) to 10 (1 step)
Type A: Configuring to a larger value reduces the noise further.
Type B: Configuring to a larger value blanks pulse noises
with small level difference from the RX signal.
4 Press and hold [NB2] or press [ESC] to end the
process.
Configuring to a value with a higher level of noise blanker
effect may cause the transceiver to malfunction and
distort the RX audio depending on the condition of the
RX signal or interfering signal.
Configuring the Blanking Duration (Type B Only)
1 Press and hold [NB2] to display the Noise Blanker
2 configuration screen.
2 While the Type A screen is displayed, press F6
[TYPE] to switch to Type B.
3
Press F2 [ ]/ F3 [ ] to select “Width”.
4 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to change the blanking duration.
Setting Value 1 to 10 (default) to 20 (1 step)
Configuring to a larger value lengthens the blanking time.
5 Press and hold [NB2] or press [ESC] to end the
process.
Configuring the NB2 Attenuation Level (Type B Only)
1 Press and hold [NB2] to display the Noise Blanker
2 configuration screen.
2 While the Type A screen is displayed, press F6
[TYPE] to switch to Type B.
3
Press F2 [ ]/ F3 [ ] to select “Depth”.
4 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to change the attenuation level.
Setting Value 1 to 20 (default) (1 step)
Configuring to a larger value increases the attenuation level.
5 Press and hold [NB2] or press [ESC] to end the
process.
REJECTING INTERFERENCE 6
6-7
93


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info