683161
34
Zoom out
Zoom in
Previous page
1/196
Next page
Common Menu Screen Operations
Pressing F [MENU TOP] returns the menu screen to the top.
Pressing F [GROUP
]/ F [GROUP ] switches the
group.
The menu item can be selected in the following ways.
Turn the [MULTI/CH] control.
Press F2 [ ]/ F3 [ ].
Press [
M.IN]/ [ ].
Press [UP] or [DOWN] on the microphone.
The setting value in the Parameter field can be selected in the
following ways.
Turn the [MULTI/CH] control.
Press [UP] or [DOWN] on the microphone.
Press F4 [–]/ F5 [+].
Press [
M.IN]/ [ ].
Press [
]/ [ ].
Pressing and holding [(RESET)] restores the altered setting
value to the default setting.
Pressing F [MORE] switches the key guide display.
Pressing F [
TOP] when configuring the sub-menu
returns the sub-menu screen to the top.
Exiting the Menu
To exit configuration or editing on the menu screen or to end the
configuration of a menu item halfway, follow the steps below. The
menu screen closes and the display returns to the normal screen.
Press [MENU] or [ESC].
It is possible to reset only the menu settings.
The menu items or default values may be altered.
When editing the screen saver message or power-on
message, pressing [MENU] will not exit the menu
screen.
Switching between the CONFIG A and CONFIG B
Operating Environments
“Operating environment” refers collectively to values configured in
the menu as well as the different settings data for operation. Two
different types of operating environment are available on this
transceiver: CONFIG A and CONFIG B. Both CONFIG A and
CONFIG B have the same functions and they can be configured
independently of each other. For example, it is possible to
configure CONFIG A for DX and CONFIG B for rag chew and
switch easily between them.
1 Press [MENU] to display the menu screen.
The current operating environment (CONFIG A or CONFIG B)
is displayed in the status bar of the menu screen. Also, data of
the operating environment can be saved to and read from a
transceiver or USB flash drive.
2 Press F7 [CONFIG].
A message appears.
Press F7 [CANCEL] to return to the Menu screen.
.
3 Press F4 [OK].
Switches from CONFIG A to CONFIG B or vice versa, and
this transceiver automatically restarts after switching is
complete.
The following are common settings between CONFIG A
and B.
Number of quick memory channels
Baud rate of COM port
Baud rate of USB connector (virtual COM port) on the
rear panel
Decoded character output
Information and data other than those below are
common between CONFIG A and B.
Advanced menu settings
LAN menu settings
Clock menu settings
Linear amplifier menu settings
Timer menu settings
Memory channel data (including quick memory and
slow scan point data)
CW/RTTY/PSK message memory data
Band memory (frequency and mode)
Broadcast band memory data
Antenna selection (including drive output selection
and antenna output selection for external receiver)
Preset data of antenna tuner
Internal audio file data of recording function (wav file)
Voice message memory data (wav file)
If the operating environment is switched while the quick
memory is called up by pressing [Q-MR>] (quick
memory), the quick memory settings will be discarded
before the operating environment switches.
3 MENU
3-2
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info