683161
27
Zoom out
Zoom in
Previous page
1/196
Next page
Rear Panel
.
Connectors and Jacks on the Rear Panel
No. Name Description Remarks
.
<ANT 1> Connector
<ANT 2> Connector
M-type coaxial connector for connecting the antenna.
.
<REF IN (10MHz)> Connector
For input of 10 MHz signals when using an external reference
frequency.
Input impedance: 50 Ω
Input: 0 dBm ±10 dB
.
<DC13.8V> Connector For connecting a regulated DC power supply.
.
<USB-A> Connector Connector for connecting a USB flash drive or USB keyboard.
.
<COM> Connector RS-232C connector for connecting a PC or external device.
.
<AT> Connector Connector for controlling an external antenna tuner.
.
<EXT.SP> Jack For connecting an external speaker.
.
<LAN> Connector
Connector for connecting a PC or LAN when running with the KNS
(KENWOOD NETWORK COMMAND SYSTEM) or for automatic
correction of the clock time.
.
<DISPLAY> Connector
DVI-I connector for connecting an external monitor. Both analog
and digital signals can be output.
.
<USB-B> Connector
Connector for connecting a PC. It is used to control this transceiver
using the ARCP-890 as well as to input and output signals for
transmission and reception via the digital communication
application of a PC. It can be switched between transmission and
reception by changing the menu setting and keying.
.
<KEY> Jack
For connecting an electronic key (straight key, bug key, external
electronic key, etc.) when running in the CW mode. This can be
configured to a jack for paddle connection in the menu.
.
<METER> Terminal For connecting a commercially available meter.
Output impedance: 4.7 Ω
Allowable open-end voltage
output: 0 to 5 V
.
<REMOTE> Connector
For connecting a linear amplifier. (Use the supplied 7-pin DIN plug
for the connection.)
.
<ACC 2> Connector
For connecting an external device such as an auxiliary equipment
for data communication. (Use the supplied 13-pin DIN plug for the
connection.)
.
<KEYPAD> Jack For connecting a self-made PF keypad.
.
<DRV> Connector For connecting a transverter or linear amplifier.
Output impedance: 50 Ω
Output: Approx. 1 mW (0 dBm)
.
<ANT OUT> Connector For connecting devices such as an external receiver.
.
<RX IN> Connector
For connecting an RX antenna, external bandpass filter, transverter
and the like.
.
<RX OUT> Connector For connecting an external bandpass filter and the like.
.
<GND> Terminal For connecting a ground wire.
NAMES AND FUNCTIONS OF PARTS 2
2-7
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-890S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-890S in the language / languages: English as an attachment in your email.

The manual is 21,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-890S

Kenwood TS-890S User Manual - German - 196 pages

Kenwood TS-890S User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info