606693
82
Zoom out
Zoom in
Previous page
1/104
Next page
76
4 Unplug CN407 (wired to the
AT connector on the
Rear Panel) from the circuit board. Lift up Cover B,
and remove the small SO-2 board from the
compartment below.
5 Insert the SO-2 unit into the SO-2 board. Solder the
five pins on the unit to the board.
6 Slide the small switch on the SO-2 board in the
direction of the SO-2 arrow.
Note:
This switch must be positioned correctly for the SO-2 unit to
function.
7 Re-install the SO-2 board in the transceiver in the
same location from which it was removed.
8 Re-position Cover B, install only 6 screws, and
replace CN407 that was unplugged in Step 4.
9 Re-position the speaker-bracket assembly, install its
screws (4 screws), and plug the speaker cable into
CN404.
10 Replace the top case and re-install its screws
(10 screws).
Note:
For more information, refer to the Instruction Manual provided
with the SO-2 unit.
14 INSTALLING OPTIONS
5 Orient the VS-2 unit with the large IC (IC1) facing
down, then install this unit on the two threaded posts
using the 2 screws.
6 Re-install Cover A (7 screws).
7 Replace the bottom case and re-install its screws
(12 screws).
Note:
For more information, refer to the Instruction Manual provided
with the VS-2 unit.
The supplied screws and cushion are not used. Keep them for
future use.
SO-2 TEMPERATURE-COMPENSATED
CRYSTAL OSCILLATOR (TCXO)
CAUTION:
Switch OFF the power and unplug the DC power cable
before beginning installation.
EQUIPMENT REQUIRED:
Large Phillips screwdriver
Small Phillips screwdriver
Pencil soldering iron (25 W)
1 Remove the top case (10 screws).
2 Unplug the speaker cable from the 2-pin connector
CN404. Remove the speaker-bracket screws
(4 screws), then lift out the entire speaker assembly.
3 Remove the remaining screws (6 screws) from
Cover B.
Speaker-bracket screws
Speaker assembly
CN404
Cover B
SO-2 board
Cover B
S
O
-2
SO-2 unit
SO-2 board
SO-2
82


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-870S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-870S in the language / languages: English as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-870S

Kenwood TS-870S User Manual - Dutch - 102 pages

Kenwood TS-870S User Manual - French - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info