606693
45
Zoom out
Zoom in
Previous page
1/104
Next page
39
FM
AGC AUTO SPLIT
RIT
TONE
XIT
FM
AGC AUTO
European Operation: In Europe, a 1750 Hz tone
is generally used to access repeaters.
Select the Subtone frequency you require via Menu
No. 57 (SUB.TONE). The available choices are
shown in the table.
Continuous or Burst Subtones?
In addition to selecting the frequency of the Subtone,
you must choose the correct Subtone duration. The
Continuous selection sends the Subtone
continuously as long as the transceiver is
transmitting. The Burst selection sends a 500 ms
Subtone burst each time the transceiver begins
transmitting.
Select either Continuous or Burst via Menu No. 58
(SUB.TONE). The default is Continuous. This
selection cannot be stored in a memory channel.
ARRL 10-METER BAND PLAN
1
Repeater frequency pairs (input/output):
29520/29620, 29540/29640, 29560/29660,
29580/29680
This completes the “FM TRANSMISSION” section.
Refer to “OPERATING AIDS” beginning on page 44 for
information about additional useful functions for
operating.
6 COMMUNICATING
6 Select the receive frequency.
7 Press [TX B] (or [TX A]) to select split operation.
This must be the same VFO as selected in
Step 1.
The Tone function automatically switches ON.
8 Select the Subtone frequency via Menu No 57
(SUB.TONE) and Menu No. 58 (SUB.TONE).
See “Selecting Subtone Frequency” and
“Continuous or Burst Subtones?” for more details
on the Subtone.
To store data selected in Steps 1 ~ 8 in a memory
channel:
9 Press [M.IN].
10 Turn the M.CH/VFO.CH control to select a channel
(excluding channel 99).
11 Press [M.IN].
To send a Subtone that is stored in memory:
12 Press [RX M.CH].
13 Turn the M.CH/VFO.CH control to select the
channel.
14 Press [PTT] or [SEND].
Note:
When operating through a repeater, over deviation caused by
speaking too loudly into the microphone can cause your signal to
“talk-off” (break up) through the repeater.
When Subtones can be transmitted, “TONE” lights on the
Display.
Memory Transfer does not copy the stored Subtone frequency
data to the VFO.
The Subtone transmitted is the tone associated with the memory
channel or the VFO frequency that is used for the transmit
function. When you transmit using a VFO frequency or the
channel 99 frequency, the Subtone selected via Menu No. 57
(SUB.TONE) and Menu No. 58 (SUB.TONE) will be used;
however, when transmitting using a memory channel, the
Subtone stored in that channel will be transmitted.
Selecting Subtone Frequency
Some 10-meter FM repeaters use CTCSS
(Continuous Tone Coded Squelch System) to
prevent other repeaters on the same frequency from
keying thus locking each other up. This repeater
access system is also referred to as Tone or PL
(“Private Line”). If CTCSS is used by a repeater in
your area, set the Subtone frequency. The default is
88.5 Hz.
01
02
03
04
05
06
07
08
09
10
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
11
12
13
14
15
16
17
18
19
20
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
21
22
23
24
25
26
27
28
29
30
136.5
141.3
146.2
151.4
156.7
162.2
167.9
173.8
179.9
186.2
31
32
33
34
35
36
37
38
39
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
1750
Freq.
(Hz)
No. No.
No.
No.
Freq.
(Hz)
Freq.
(Hz)
Freq.
(Hz)
CW
RTTY
Packet
Beacons
Phone
(AM)
Satellite downlinks
Repeater inputs
FM simplex calling
Repeater outputs
28000~28070
28070~28150
28120~28189
28190~28300
28300~29300
(29000~29200)
29300~29510
29510~29590
29600
29610~29700
Frequency Range (kHz)
Mode/Activity
1
1
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-870S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-870S in the language / languages: English as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-870S

Kenwood TS-870S User Manual - Dutch - 102 pages

Kenwood TS-870S User Manual - French - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info