606692
44
Zoom out
Zoom in
Previous page
1/96
Next page
36
7 COMMUNICATING AIDS
Checking CW Messages without Transmitting
1 Press [CW/FSK (REV)] until you select CW
mode.
• “CW” appears.
2 If Break-in is ON, press [VOX (LEV)] to turn
VOX OFF.
3 Press [CH1 (REC)], [CH2 (REC)], [CH3
(REC)], or [RX/4 (REC)] to select the channel
to be played back.
The message is played back.
When Menu No. 62 is “oFF”, press and
hold the current playback channel key to
repeatedly play back the message saved
to that key (a display such as “CP 1111”
appears for the channel key you pressed.).
To cancel the playback, press any channel
key or [CLR].
To play back the messages stored in the
other channels in sequence, press the
corresponding channel keys during playback.
Up to 4 channels can be queued at the
same time. (Repeat playback, by pressing
and holding the keys, does not work during
consecutive message playback.)
While playing back the messages, you can
also adjust the keyer speed by pressing
[KEY (DELAY)] and turning the MULTI/CH
control.
To interrupt playback, press [CLR].
Transmitting CW Messages
Messages can be transmitted using Semi Break-in/
Full Break-in or manual TX/ RX switching.
1 Press [CW/FSK (REV)] until you select CW
mode.
• “CW” appears.
2 To use Semi Break-in/ Full Break-in, press
[VOX (LEV)].
• “ appears.
If you are not using Semi Break-in/ Full
Break-in, press [SEND].
3 Press [CH1 (REC)], [CH2 (REC)], [CH3
(REC)], or [RX/4 (REC)] select the channel to
be played back.
The message is played back and transmitted
automatically.
To transmit the messages stored in the
other channels in sequence, press the
corresponding channel keys during playback.
Up to 4 channels can be queued at the
same time.
While playing back the messages, you can
also adjust the keyer speed by pressing
[KEY (DELAY)] and turning the MULTI/CH
control.
• To cancel transmission, press [CLR].
Erasing a CW Message
1 Press and hold [CH1 (REC)], [CH2 (REC)],
[CH3 (REC)], or [RX/4 (REC)] to select the
message you want to erase.
“CP n – –” appears, where “n” represents the
channel number.
2 To erase the CW message, press [CLR] while
continuing to hold the same key as in step 1
([CH1 (REC)], [CH2 (REC)], [CH3 (REC)], or
[RX/4 (REC)]).
A beep sounds and the message is erased.
Changing the Inter-message Interval Time
For the message playback repeat, access Menu
No. 62 and select “on”. You can also change the
interval playback time of the message. Access
Menu No. 63 and select the time in the range of 0
to 60 seconds, in steps of 1 second.
Note: Menu Nos. 56 and 57 settings are shared with the
voice communication modes when the optional VGS-1 is
installed.
Changing the CW Sidetone Volume
Turning the AF control does not change the CW
sidetone playback volume. To change the CW
sidetone volume, access Menu No. 06 and select
“oFF”, or “1” to “20”. The default is “10”.
Insert Keying
If you operate a CW keyer manually while playing
back a recorded CW message, the transceiver
stops playing back the message. However, during
contests or regular QSOs, you may sometimes
want to insert a different number or message at a
certain point in the recorded message.
In this case, fi rst record the CW message as
usual {page 35}, without the additional number or
message you want to insert. Then, access Menu
No. 39 and select “on”.
Now, if you operate a CW keyer while you play
back a recorded message, the transceiver pauses
the playback of the recorded message, instead of
stopping it. When you fi nish sending the number or
message with the keyer, the transceiver resumes
playback of the message.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-590SG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-590SG in the language / languages: English as an attachment in your email.

The manual is 4,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-590SG

Kenwood TS-590SG User Manual - German - 96 pages

Kenwood TS-590SG User Manual - Dutch - 96 pages

Kenwood TS-590SG User Manual - French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info