606692
33
Zoom out
Zoom in
Previous page
1/96
Next page
25
ENHANCED COMMUNICATIONS 6
frequency. You will soon learn the rhythm of the
DX station and the pileup. The more profi cient you
become at using this function, the more DX stations
you will contact.
Note:
TF-SET is disabled while transmitting.
You can change the transmission frequency even when the
Frequency lock function is ON.
An RIT offset frequency is not added; however, an XIT offset
frequency is added to the transmit frequency during TF-SET.
The TF-SET function does not operate in Simplex mode.
However, when the XIT function is ON and the RIT function
is OFF, the TF-SET function will operate in Simplex mode. In
this situation, you can set the XIT frequency while operating
TF-SET by rotating the Tuning knob or pressing the MIC [UP]
/ MIC [DOWN] keys.
SHIFTABLE RX FREQUENCY DURING SPLIT
TRANSMISSION
As the factory default setting, when rotating the Tuning
knob during split transmission, the transmit frequency
will change. By following the procedures below, when
rotating the Tuning knob during split transmission, you
can change the receive frequency.
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
turn the MULTI/CH control to select Menu No. 20.
2 Press [M.IN]/ [SCAN (SG.SEL)] to select “on”
3 Press [MENU] to exit Menu mode.
When you switch the transceiver ON while this
function is set to ON, the decimal point at the
right end digit of the main display fl ashes for
approximately 2 seconds after the Power On
message is displayed.
FM REPEATER OPERATION
Most Amateur radio voice repeaters use a separate
reception and transmission frequency. The
transmission frequency may be higher or lower than
the reception frequency. In addition, some repeaters
may require the transceiver to transmit a subtone
before the repeater can be used.
Compared to simplex communication, you can
usually transmit over much greater distances by
using a repeater. Repeaters are typically located
on a mountain top or other elevated location. Often
they operate at higher ERP (Effective Radiated
Power) than a typical station. This combination of
elevation and high ERP allows communications over
considerable distances.
HF/ 6 m band repeaters usually operate in the
29 MHz FM sub-band and 51-54 MHz band. This
special service combines the advantages of FM
operation, good fi delity with noise and interference
immunity, with the excitement of HF DX (long
distance) communications. Even on a quiet day,
10 m FM provides reliable around-town
communications with the potential for sudden DX from
across the country or around the world.
Note:
When programming 2 separate frequencies using 2 VFOs,
be sure to select FM mode on both VFOs.
When operating through a repeater, over deviation caused
by speaking too loudly into the microphone can cause your
signal to “talk-off” (break up) through the repeater.
29.520 MHz
88.5 Hz
29.520 MHz
88.5 Hz
29.620 MHz
29.620 MHz
1 Press [A/B (A=B)] to select VFO A or VFO B.
• “ or “ appears to show which VFO is
selected.
2 Turn the Tuning control or the MULTI/CH control to
select the reception frequency.
3 Press [FM/AM (FM-N)] to select FM mode.
4 Press and hold [A/B (A=B)] to duplicate the
frequencies and other data to the other VFO.
5 Turn the Tuning control or the MULTI/CH control to
select the transmission frequency.
6 Press [AGC/T (SEL] to turn the Tone function ON if
the repeater requires a subtone.
• “
appears.
Refer to “Selecting a Tone Frequency” for more
details on the subtone {page 26}.
To quit the Subtone function, press [AGC/T (SEL)]
twice.
7 Press [SPLIT].
• “ ” appears.
8 Press [A/B (A=B)] to return to the original
reception frequency.
9 Press Mic [PTT] to transmit.
The VFO changes to the other VFO to transmit.
Each time you press [A/B (A=B)], the reception
and transmission frequencies are swapped.
10 Press [SPLIT] to quit split-frequency operation.
• “
disappears.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-590SG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-590SG in the language / languages: English as an attachment in your email.

The manual is 4,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-590SG

Kenwood TS-590SG User Manual - German - 96 pages

Kenwood TS-590SG User Manual - Dutch - 96 pages

Kenwood TS-590SG User Manual - French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info