606692
10
Zoom out
Zoom in
Previous page
1/96
Next page
2
1 INSTALLATION
UTILIZING THE BAIL
This transceiver is equipped with a bail so that you
can angle the transceiver. The bail is located on the
bottom of the transceiver. Pull the bail forward to the
limit as shown.
REPLACING FUSES
The following fuses are used in the TS-590SG
transceiver. If a fuse blows, determine the cause
then correct the problem. Only after the problem
has been resolved, replace the blown fuse with a
new one with the specifi ed ratings. If newly installed
fuses continue to blow, disconnect the power plug and
contact a KENWOOD service center or your dealer for
assistance.
Fuse Location Fuse Current Rating
TS-590SG Transceiver
4 A
(for external
antenna tuner)
Supplied DC power cable 25 A
Fuse (4 A)
Fuse (25 A)
Fuse (25 A)
ACCESSORY CONNECTIONS
FRONT PANEL
Headphones (PHONES)
Connect monaural or stereo headphones with a
4 to 32 (normal 8 ) impedance. This jack
accepts a 6.3 mm (1/4") diameter, 2-conductor
(mono) or 3-conductor (stereo) plug. After
connecting the headphones, you will hear no
sound from the internal (or optional external)
Speaker/Microphone (MIC).
Note: Using a high impedance headphone set causes the
volume to be louder.
Microphone (MIC)
Connect a microphone with a 250 to 600
impedance. Fully insert the connector, then
screw the retaining ring clockwise until secure.
Compatible microphones include the MC-43S,
MC-47, MC-52DM, MC-60A, MC-80, MC-85, and
MC-90.
Note: Do not use the MC-44, MC-44DM, MC-45, MC-45E,
MC-45DM, MC-45DME, or MC-53DM microphones.
REAR PANEL
External Speaker (EXT.SP)
On the rear panel of the transceiver, there is an
external speaker jack. If an external speaker is
connected to EXP.SP, the transceiver internal
speaker will mute. Use only external speakers with
an impedance of 4 to 8 (8 nominal). This jack
accepts only 3.5 mm (1/8") diameter, 2-conductor
(mono) plugs.
Do not connect headphones to this jack. The high audio
output of this jack could damage your hearing.
Keys for CW (PADDLE and KEY)
For CW operation while using the internal
electronic keyer, connect a keyer paddle to the
PADDLE jack.
For CW operation without using the internal
electronic keyer, connect a straight key,
semi-automatic key (bug), electronic keyer,
or the CW keyed output from a Multi mode
Communications Processor (MCP) to the KEY jack.
The PADDLE and KEY jacks mate with a 6.3 mm
(1/4") 3-conductor plug and a 3.5 mm (1/8")
2-conductor plug, respectively. External electronic
keyers or MCPs must use positive keying to be
compatible with this transceiver. Use a shielded
cable between the key and the transceiver.
Note: Due to the functionality of the internal electronic
keyer, you may nd it unnecessary to connect both a paddle
and another type of keyer unless you want to use a
PC-based keyer for CW. Read the “ELECTRONIC KEYER”
section {page 34} to become familiar with the internal keyer.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-590SG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-590SG in the language / languages: English as an attachment in your email.

The manual is 4,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-590SG

Kenwood TS-590SG User Manual - German - 96 pages

Kenwood TS-590SG User Manual - Dutch - 96 pages

Kenwood TS-590SG User Manual - French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info