682841
72
Zoom out
Zoom in
Previous page
1/89
Next page
66
16 MAINTENANCE
1 The SQL control is fully clockwise.
2 The Attenuator function is ON.
3 [SEND] was pressed, and the
transceiver is now in transmit
mode.
4 Mic [PTT] is pressed.
5 The receive bandwidth was
incorrectly set.
6 The wrong antenna connector
(ANT 1/ANT 2) was selected.
7 The receive preamplifier is OFF.
The RF control was set too low.
The wrong modulation mode was
selected.
1 The SQL control was not set
correctly.
2 Less than two memory channels
were unlocked.
3 Less than two memory channels
were programmed.
With Group Scan selected, the
channel you want to scan is in a
different group.
The start and end frequencies are
identical.
The impedance of the coaxial cable
and antenna was not matched.
•Tuning does not successfully finish
depending on conditions although
the SWR meter indicates smaller
than 3:1.
The SWR of the antenna system is too
high.
1 The microphone plug was not
inserted completely into the MIC
connector.
2 The Transmit Inhibit function is ON.
3 CW or FSK was selected instead of
a voice mode.
4 The filter for digital operation was
selected.
5 The wrong antenna connector
(ANT 1/ANT 2) was selected.
No signals are
received or receive
sensitivity seems
poor.
No signals are
received or receive
sensitivity seems
poor; S-meter is
reading full scale.
Received signals are
totally unintelligible.
Memory Scan will not
start scanning.
Memory Scan will not
scan one of the
stored channels; the
desired channel is
NOT locked out.
Program Scan will
not start scanning.
Tuning does not
finish successfully.
The internal tuner is
bypassed
immediately after
tuning is started.
You cannot transmit
even though you
press Mic [PTT] or
transmissions result
in no contacts.
1 Turn the SQL control
counterclockwise.
2 Press [ATT] to switch OFF function.
3 Press [SEND] to return to receive
mode.
4 Release Mic [PTT].
5 Review sections “IF FILTER” and
“CHANGING RECEIVE
BANDWIDTH”, and set the controls
accordingly.
6 Press [ANT] to select the other
antenna connector.
7 Press [PRE-AMP] to switch ON
function.
Turn the RF control fully clockwise.
Press [LSB/USB], [CW/FSK], or
[FM/AM] to select the correct
modulation mode.
1 Adjust the SQL control to just
eliminate background noise.
2 Unlock at least two memory
channels.
3 Store data in at least two memory
channels.
Select the group that contains the
memory channel you want to scan.
Store different start and end
frequencies.
Adjust the antenna system to lower the
SWR.
Adjust the antenna system to lower the
SWR.
1 Turn OFF the power, ensure the MIC
connector has no foreign objects in
it, then plug in the connector.
Secure the connector with the
locking ring.
2 Change Menu No. 38 to OFF.
3 Press [LSB/USB] or [FM/AM] to
select a voice mode.
4 Change Menu No. 32 to OFF.
5 Press [ANT] to select the other
antenna connector.
14
37
15
15
36,37
48
37
13
14
14
44
39
47
43
1
52
3
18
14
18
48
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-570S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-570S in the language / languages: English as an attachment in your email.

The manual is 4,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info