682841
59
Zoom out
Zoom in
Previous page
1/89
Next page
53
12 OPERATOR CONVENIENCES
6 To record a message in another channel, start with
step 3.
Note:
To erase a message, press and hold the desired channel button,
and press
[CLR]
.
Pressing the
[ ]
(POWER) switch cancels recording in progress
and clears the memory channel.
MESSAGE PLAYBACK
You can play back the message in channel 1, 2, or 3 to
check or to send. It is also possible to make a longer
linked message, by consecutively playing back the
messages of more than one channel.
You can even send a longer linked message repeatedly
by using the Repeat function. To switch this function
ON, access Menu No. 23 and select ON. The default is
OFF.
Note:
Pressing the
[ ]
(POWER) switch cancels playback in progress.
The settings in Menu No. 23 and No. 24 are shared with CW
Message Playback described in “CW MESSAGE MEMORY”
{page 35}.
Checking Messages
1 Select SSB, FM, or AM.
Use the same mode for transmitting and
receiving.
2 If VOX is ON, press [VOX] to switch the function
OFF.
3 Press [CH 1], [CH 2], or [CH 3], depending on
which channel you want to check.
For example, “AP 1– –” appears while
playing back the message in channel 1.
•To interrupt playback, press [CLR].
4 To play back another message in sequence,
press the corresponding [CH 1], [CH 2], or
[CH3] while playing back the first message.
Up to three channels can be queued at the
same time.
DRU-3A DIGITAL RECORDING UNIT
(OPTIONAL)
The optional DRU-3A unit allows you to record a voice
message on up to 3 channels. After recording a
message via your transceiver microphone, you can then
send that message.
The maximum recording time for each channel is as
follows:
Channel 1: Approx. 30 sec
Channel 2: Approx. 15 sec
Channel 3: Approx. 15 sec
The DRU-3A is useful in many situations:
DX chasing or contest operation where repeated
calls are necessary for extended periods of time
Checking interference complaints to other equipment
(lets you be in two places at one time)
Checking or adjusting your transmit signal or your
antenna(s) if it’s not convenient to be sitting in front
of your microphone
Helping a friend adjust his antenna or receive when
he needs repeated test transmissions from you
For information on how to install the DRU-3A unit, refer
to “INSTALLING OPTIONS” {page 57}.
RECORDING MESSAGES
This section explains how to record a single message.
1 Select SSB, FM, or AM.
Use the same mode for transmitting and
receiving.
2 If VOX is ON, press [VOX] to switch the function
OFF.
3 Press [REC] to enter the Record Standby mode.
“AP –” appears.
•To exit the Record Standby mode and quit
recording your message, press [CLR].
4 Press and hold down [CH 1], [CH 2], or [CH 3] and
begin speaking into your microphone.
There are three channels for recording
messages. Press the button that corresponds to
the channel that you want to use.
5 Release the button pressed in step 4 when you have
finished recording your message.
Also when the maximum recording time passes,
recording stops.
The content of the channel is overwritten with the
new message.
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-570S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-570S in the language / languages: English as an attachment in your email.

The manual is 4,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info